Installation Instructions

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT Save these instructions for local inspector’s use.

IMPORTANT Observe all governing codes and ordinances.

Note to Installer – Be sure to leave these instructions with the Consumer.

Note to Consumer – Keep these instructions for future reference.

Skill Level – Installation of this vent hood requires basic mechanical and electrical skills.

Completion time – 1 to 3 hours.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the Warranty.

CAUTION:

Due to the weight and size of these vent hoods and to reduce the risk of personal injury or damage to the product, THREE PEOPLE ARE REQUIRED

FOR PROPER INSTALLATION.

PRUDENCE

À cause du poids et des dimensions du ces hottes et pour réduire les risques de blessures ou de dommages du produit, IL FAUT TROIS PERSONNES

POUR FAIRE UNE INSTALLATION CORRECTE.

WARNING:

To reduce the risk of fire or electrical shock, do not use this range hood with any external solid-state speed control device. Any such alteration from original factory wiring could result in damage to the unit and/or create an electrical safety hazard.

AVERTISSEMENT

Pour réduire le risque d’incendie ou de choc électrique, il ne faut pas utiliser cette hotte avec un régulateur de vitesse électronique externe. Toute modification de ce type du branchement d’usine peute endommager l’appareil ou créer un risque de choc électrique.

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

2

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR

INJURY, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

B. Before servicing or cleaning unit, switch power off at the service panel and lock service panel to prevent power from being switched on accidentally. If the service panel cannot be locked, fasten a tag or prominent warning label to the panel.

AVERTISSEMENT

POUR RÉDUIRE LE RISQUE D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURES, IL

FAUT OBSERVER LES REGLES SUIVANTES:

A. Utiliser cet appareil uniquement de la maniére

prévue par le fabricant. En cas de question, consulter le fabricant.

B. Avant toute intervention ou nettoyage, couper l’alimentation électrique au disjoncteur et verrouiller le panneau du disjoncteur pour éviter la mise sous tension accidentelle. S’il n’est pas possible de verrouiller le panneau du disconcteur, attacher un placard ou une étiquette trés visible au panneau.

For general ventilating use only. Do not use to exhaust hazardous or explosive materials or vapors.

Structural framing, installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards including fire-rated construction.

Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

Local codes vary. Installation electrical connections and grounding must comply with applicable codes. In the absence of local codes, the vent should be installed in accordance with National Electrical Code ANSI/NFPA 70-1990 or latest edition.

CAUTION: To reduce risk of fire and to properly exhaust air, be sure to duct

air outside – Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

PRUDENCE Il faut prendre soin d’installer un conduit vers l’extérieur pour réduire le risque d’incendie et pouvoir

évacuer l’air correctement. Il ne faut pas évacuer l’air correctement. Il ne faut pas évacuer l’air dans l’espace entre les parois d’un mur, un plafond ou un grenier, un espace sanitaire ou un garage.

Page 2
Image 2
GE ZV541, ZV421 For Proper Installation, Pour Faire UNE Installation Correcte, Faut Observer LES Regles Suivantes

ZV421, ZV541 specifications

The GE ZV541 and ZV421 are prominent offerings in the realm of multi-function medical imaging devices, widely recognized for their advanced features, robust technologies, and user-friendly characteristics that cater to the needs of healthcare professionals.

The GE ZV541 is designed primarily for a wide range of imaging applications, including vascular, cardiac, and general imaging. One of its most outstanding features is its cutting-edge imaging technology, which employs advanced digital signal processing to produce high-resolution images with exceptional clarity. This enables practitioners to make accurate diagnoses and evaluate complex conditions with confidence. The ZV541 also integrates automated image optimization algorithms, ensuring that images are consistently of high quality, regardless of the operator's experience level.

Additionally, the ZV541 offers a range of versatility with its multi-modal capabilities, allowing it to perform ultrasound imaging alongside other imaging techniques. This flexibility is critical in a busy clinical environment where different modalities might be required for patient assessment. Its user-friendly interface simplifies navigation, enabling practitioners to focus more on patient care rather than on the technical complexities of the equipment.

On the other hand, the GE ZV421 excels in providing compact and reliable imaging solutions, particularly in settings where space and portability are key considerations. It retains many of the advanced imaging capabilities of its larger counterpart while being designed for ease of transport and quick setup. The ZV421 incorporates similar digital enhancement technologies that ensure high-quality output with quick turnaround times.

Both devices are equipped with intuitive touchscreen controls that enhance the user experience, making it easier to adjust settings and quickly access frequently used features. They also come with integrated data management systems that facilitate seamless sharing and storage of patient data, complying with modern healthcare standards for efficiency and security.

In summary, the GE ZV541 and ZV421 combine state-of-the-art imaging technologies with versatility and user-friendly designs. These devices are ideal for healthcare environments that require reliable performance along with superior diagnostic capabilities. Their features not only improve workflow but also enhance the overall quality of patient care, making them invaluable tools in contemporary medical practices.