Sanyo PLC-WXU300K owner manual Lamp control, Lamp life control

Page 55

Setting

Lamp control

Lamp control

This function allows you to change brightness of the screen.

Normal	Normal brightness
Eco	Lower brightness reduces the lamp
	power consumption and extends the
	lamp life.

Lamp life control

Select the lamp operation when the total lighting time of a lamp exceeds the recommended total hours of use.

Mode 1	A lamp can be turned on even after
	exceeding the recommended total
Mode 2	hours of use.
Mode 2	A lamp can be turned on even after
	exceeding the recommended total
	hours of use. But the projector turns off
	automatically after 3 minutes.

Note:

•Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized.

•If Mode 2 has been selected and the projection lamp exceeds the recommended total hours of use, the replacement icon will be displayed at the time of power- on. Then the projector will turn off after 3 minutes.

Lamp replacement icon

•The Lamp replacement icon will not appear when the Display function is set to Off (p.46), during "FREEZE button" (p.25), or "NO SHOW button" (p.26).

Remote control

This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control interference when operating several projectors or video equipment at the same time.

When operating the projector in Code 2, both the projector and the remote control must be switched to Code 2.

To change the code for the projector:

Select either Code 1 or Code 2 in this Setting Menu.

To change the code for the remote control:

Press and hold both the MENU and IMAGE buttons together for 5 seconds or more. After changing the code, make sure the remote control operates properly.

Lamp life control

Power management	Off
On start	Off

Remote control

Note:

•When different codes are set on the projector and on the remote control, any operation cannot be made. In that case, switch the code on the remote control to fit the code on the projector.

•If the batteries are removed from the remote control for a long period of time, the remote control code will be reset.

55

Image 55

Contents Network Supported Model PLC-WXU300 PLC-WXU300KFeatures and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Installing the Projector in Proper Position Safety Instructions Air CirculationMoving the Projector Compliance AC Power Cord RequirementAC Power Cord for the United States and Canada AC Power Cord for the United KingdomBottom Part Names and FunctionsFront Back ⑦ ⑧ ⑤ LAN Connection Terminal Part Names and Functions⑧ Warning indicator ① Select button ⑦ Auto Setup button② Point Volume +/- buttons ⑤ Power indicatorPart Names and Functions Remote Control Menu button Image button Remote Control Operating RangeRemote Control Code Two AAA size batteriesAdjustable Feet InstallationPositioning the Projector Cables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment For Continental Europe For the U..K Installation Connecting the AC Power CordNote Projector side AC outlet sideTurning On the Projector Input signal guidance windowVideo / PC selection window Input signal guidance window Basic OperationPIN Code Input Dialog Box What is PIN code?Basic Operation Enter a PIN codeBasic Operation Turning Off the Projector On-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Top Control Input  Image adjust Setting Basic Operation Menu BarNotes Basic Operation Zoom and Focus AdjustmentAuto Setup Function Keystone CorrectionDirect Operation Basic Operation Sound AdjustmentMenu Operation Basic Operation Remote Control Operation Screen button Timer buttonNo Show button Image buttonInput Source Selection Computer 1 RGB Computer InputInput Menu Computer 2 button Computer 2RGB Computer Input Input Source Selection Computer 2 RGBPC System Menu Auto ModeComputer Input Computer System Selection Selecting Computer System ManuallyAuto PC adj Computer Input Auto PC adjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC adjustment Computer Input ResetMode free Note Display area H/V cannot be selected when 480iImage select Menu Computer Input Image Mode SelectionImage adjust Menu Computer Input Image AdjustmentTrue Screen Size AdjustmentScreen Menu NormalDigital zoom CustomPosition H/V For zooming in and out the images Digital zoom +Video Video InputInput Source Selection Video, S-video Input MenuRGB Scart ComponentOr Computer 1Component and then press Video Input Video System SelectionVideo or S-video Component AV System Menu ComponentCinema Video Input Image Mode SelectionBlackboard or Colorboard Video Input Image AdjustmentColor TintProgressive Video InputStore Menu Noise reductionWide Video Input Screen Size AdjustmentScreen Menu ZoomLanguage SettingSetting Setting MenuAuto Keystone Auto setupAuto setup Input searchDisplay Power off? p.20Keystone BackgroundLogo select Logo Logo and Logo PIN code lock settingsDefault Logo selectCapture Capture Logo PIN code lockOff Logo PIN code lock Logo PIN code change Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code change Enter a Logo PIN codeCeiling Rear Hdmi setup Selecting the Main picture or Sub picture Switching of the Input SourcePicture in Picture Mode. . . . . P in P By P Off Subpicture sizePower management Standby modeOn start On startOff, CC1, CC2, CC3 or CC4 Closed captionFrom Color to White Lamp life control Lamp controlPIN code lock Key lockSecurity Key lock and PIN code lock Key lockPIN code change Change the PIN code lock settingEnter a PIN code Change the PIN code Filter counter Filter counterFan Fan controlFactory default Input Source Information Display InformationProjector is shut down and the Warning Maintenance and CleaningIndicator is blinking red Indicator lights redResetting the Filter Counter Maintenance and Cleaning Cleaning the FiltersFilter counter Cleaning the Projection Lens Maintenance and Cleaning Attaching the Lens CapCleaning the Projector Cabinet Service Parts No 343 Maintenance and Cleaning Lamp ReplacementLamp Replace indicator Maintenance and Cleaning Lamp Handling PrecautionsAppendix TroubleshootingAppendix PIN code dialog box appears Remote Control doesIndicator blinks or lights Image is distorted or runs offAppendix Computer Input Appendix Menu TreeComputer Input/Video Input SoundVideo Input SettingSystem Image select Image adjust Screen 1080iSettingIndicators Appendix Indicators and Projector ConditionON-SCREEN Resolution Appendix Compatible Computer SpecificationsSXGA1 Appendix List of Picture in Picture Appendix Technical Specifications Optional Parts Appendix PJ Link Notice Terminal Analog RGB Mini D-sub 15 pin Appendix Configurations of TerminalsHdmi 19 PIN Type a PIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No Unit mminch Appendix DimensionsKE5AC