Sanyo HF10000L owner manual Color temp, White balance Red, White balance Green, White balance Blue

Page 41

Computer Input

MENU

 

Return to the IMAGE ADJUST Menu. Any settings that

 

have been changed will not be stored. To store the changed

 

settings, be sure to select “LIST” and go to the COLOR

 

MANAGEMENT LIST.

4

In the COLOR MANAGEMENT LIST, the adjusted color data

are checkmarked. You can decide whether or not to apply the

adjusted color data in the list to the projected image (see below).

LIST MODE

Clear the check mark if you do not want to apply the adjusted color data; select the check mark and then press the SELECT button. The check mark disappears.

COLOR PALETTE

Return to the COLOR SELECTION mode so that you can readjust the setting for the color in that line. (This option is not available if the check mark is cleared.)

COLOR SELECTION MODE

Level and phase

Gamma

adjustment palette.

adjustment palette.

LIST

COLOR M.

MENU

DEL

 

LIST MODE

Select the DEL box if you want to delete the adjusted data.

 

 

Press the SELECT button and a confirmation box appears and

 

 

then select [Yes].

 

 

ALL DEL

Delete all the data in the list. Press the SELECT button and a confirmation box appears and then select [Yes].

MENU

The same function as stated above.

COLOR M.

The same function as stated above.

COLOR PALETTE

DEL

Color temp.

Use the Point 7 8 buttons to select the desired Color temp. level (XLow, Low, Mid or High).

White balance (Red)

Press the Point 7 button to lighten red tone; press the Point

8button to deepen red tone (from 0 to 63).

ALL DEL

MENU

COLOR M.

White balance (Green)

Press the Point 7 button to lighten green tone; press the Point 8 button to deepen green tone (from 0 to 63).

White balance (Blue)

Press the Point 7 button to lighten blue tone; press the Point 8 button to deepen blue tone (from 0 to 63).

41

Image 41
Contents Model PLC-HF10000L Functionally Rich Motor-driven Lens Shift Features and DesignTable of Contents To The Owner Safety PrecautionSafety Instructions Top Panel Safety InstructionsAir Circulation Positioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorAC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Federal Communications Commission NoticeBack Part Names and FunctionsFront Part Names and Functions Terminals and ConnectorsSide Control Side Control and IndicatorsIndicators Timer button Signal Emission indicator9IMAGE Adjust button STAND-BY buttonWired Remote Control Remote Control Battery InstallationRemote Control Receivers and Operating Range Remote Control Codes Attaching the Strap InstallationLens Installation Lens Shift Adjustment InstallationPicture Level and Pitch Adjustment Positioning ProjectorTerminals of Projector Replacement of TerminalTerminals of the projector Connecting to ComputerCables used for connection Hdmi RGB Scart Connecting to Video EquipmentTo loosen the cable tie Attaching the Cable TieProjector side Connecting the AC Power CordFor the U.K For the U.S.A. and Canada For Continental EuropeWhen using remote control When using side controlBasic Operation Turning On the ProjectorBasic Operation What is PIN code?Turning Off the Projector Direct OFF functionSelect button On-screen menu Basic Operation How to Operate the On-Screen MenuCurrently Selected item is Set item is Highlighted in orange MarkedBasic Operation Main Menu Information Basic Operation Operating with Projector ControlBasic Operation Operating with Remote Control Light button Timer buttonFreeze button Filter buttonCorner correction Basic Operation Keystone CorrectionStandard Input Selection Remote Control OperationDirect Operation Side ControlRgbpc analog Input Selection Computer Input Source SelectionMenu Operation RGBScart Input Selection Video Input Source SelectionRgbpc digital VideoComputer System Selection Computer InputAutomatic Multi-Scan System Selecting Computer System ManuallyTo store the adjusted parameters Computer Input Auto PC AdjustmentDirect Operation Auto PC adjComputer Input Manual PC Adjustment Mode free ResetComputer Input StoreReal Image select StandardDynamic ImageImage Adjust Menu Computer Input Image AdjustmentContrast BrightnessWhite balance Red Color tempWhite balance Green White balance BlueAuto picture control Offset Red/Green/BlueAdvanced color SharpnessComputer Input Screen Size Adjustment Digital zoom Custom adjDigital zoom + Corner correction KeystoneCorner pattern CeilingVideo System Selection Video InputCinema Video InputImage select menu Standard Tint Video Input Image AdjustmentColor Offset Red/Green/Blue Progressive Noise reductionNatural wide Video Input Screen Size AdjustmentChoose a Corner pattern mode among Red, White, Blue, and Off Settings SettingsLamp control Lamp modeBackground Lamp interval Lamp life controlPicture in Picture Picture in PictureDisplay position setting screen Color matching Edge blendingAdvanced color matching Measured information Advanced color matching Test patternLogo Logo and Logo PIN code lock settings Hdmi setupLogo select CaptureLogo PIN code lock Change the Logo PIN code lock settingChange Logo PIN code To enter a Logo PIN code lock To change the Logo PIN codeFilter control To change the code for the remote controlFan control To change the code for the projectorDirect on Power managementPIN code lock Security Key lock and PIN code lockKey lock To enter a PIN code To change the PIN code lock settingTo change PIN code To change the PIN codeShutter Projector IDClosed caption Video delay controlAppear at turning on and selecting input source Filter counterFactory default TimerEdge blending How To Overlap the Projection ImagesHow to Overlap the Projection Images on a Screen Color matching How to Overlap the Projection ImagesFilter Instructions Maintenance and CareReset the filter counter and the scroll counter p.73 Maintenance and CareService Parts Code 610 335 Replacing the Filter CartridgeScroll counter Maintenance and Care Resetting the Filter CounterResetting the Scroll Counter Yellow Lamp Lamp ManagementDim Lamp Red LampLamp 1 / 2 Replace indicators Lamp ReplacementIndicators Lamp Handling Precautions Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below Lamp indicator lights on and other indicators blinkAppendix TroubleshootingImage is out of focus AppendixShutter does not Computer Input Menu TreeComputer Input/HDMI Input/Video Input Hdmi Input/Video Input Image adjustVideo Input Image select ScreenMode1 Off SettingProjector is operating normally Indicators and Projector ConditionIndicators Lamp Replace 1 Projector is detecting abnormal conditionIf the Filter counter reached a time set in the timer KHz Compatible Computer SpecificationsFreq Svga Freq.kHz Freq.Hz Supported Signal Format for Optional BoardTechnical Specifications Projector Input PJLink Input Parameter Optional PartsPJ Link Notice Control Port Connector D-sub 9 pin Configurations of TerminalsAnalog TERMINALMini D-sub 15 pin USB PORTSeries B Hdmi TERMINAL19 pin Type aLogo PIN Code Lock No PIN Code Number MemoPIN Code Lock No Unit inch mm DimensionsList of Picture in Picture Format Serial Control InterfaceExample Status Read Commands KG2A