Sanyo HF10000L owner manual Lamp Handling Precautions

Page 76

Maintenance and Care

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer.

Model No. of your projector

:

PLC-HF10000L

Replacement Lamp Type No.

:

POA-LMP146

 

 

 

(Service Parts No. 610 351 5939)

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly.

Improper handling may result in accidents, injury, or create a fire hazard.

Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

If the projector indicates that the lamp should be replaced, i.e., if the LAMP 1/2 REPLACE indicators light up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP 1/2 REPLACE indicators lighted may increase the risk of lamp explosion.

Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES,THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service center for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

76

Image 76
Contents Model PLC-HF10000L Features and Design Functionally Rich Motor-driven Lens ShiftTable of Contents Safety Precaution To The OwnerSafety Instructions Air Circulation Safety InstructionsTop Panel Installing the Projector in Proper Directions Positioning PrecautionsMoving the Projector Transporting the ProjectorAC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Federal Communications Commission NoticeFront Part Names and FunctionsBack Terminals and Connectors Part Names and FunctionsSide Control and Indicators Side ControlIndicators Signal Emission indicator Timer button9IMAGE Adjust button STAND-BY buttonRemote Control Receivers and Operating Range Remote Control Battery InstallationWired Remote Control Remote Control Codes Lens Installation InstallationAttaching the Strap Installation Lens Shift AdjustmentPicture Level and Pitch Adjustment Positioning ProjectorReplacement of Terminal Terminals of ProjectorCables used for connection Connecting to ComputerTerminals of the projector Connecting to Video Equipment Hdmi RGB ScartAttaching the Cable Tie To loosen the cable tieConnecting the AC Power Cord Projector sideFor the U.K For the U.S.A. and Canada For Continental EuropeWhen using side control When using remote controlBasic Operation Turning On the ProjectorWhat is PIN code? Basic OperationTurning Off the Projector Direct OFF functionBasic Operation How to Operate the On-Screen Menu Select button On-screen menuCurrently Selected item is Set item is Highlighted in orange MarkedBasic Operation Main Menu Basic Operation Operating with Projector Control InformationBasic Operation Operating with Remote Control Timer button Light buttonFreeze button Filter buttonStandard Basic Operation Keystone CorrectionCorner correction Remote Control Operation Input SelectionDirect Operation Side ControlMenu Operation Input Selection Computer Input Source SelectionRgbpc analog Input Selection Video Input Source Selection RGBScartRgbpc digital VideoComputer Input Computer System SelectionAutomatic Multi-Scan System Selecting Computer System ManuallyComputer Input Auto PC Adjustment To store the adjusted parametersDirect Operation Auto PC adjComputer Input Manual PC Adjustment Reset Mode freeComputer Input StoreImage select Standard RealDynamic ImageComputer Input Image Adjustment Image Adjust MenuContrast BrightnessColor temp White balance RedWhite balance Green White balance BlueOffset Red/Green/Blue Auto picture controlAdvanced color SharpnessComputer Input Screen Size Adjustment Digital zoom + Custom adjDigital zoom Keystone Corner correctionCorner pattern CeilingVideo Input Video System SelectionImage select menu Standard Video InputCinema Color Video Input Image AdjustmentTint Offset Red/Green/Blue Noise reduction ProgressiveVideo Input Screen Size Adjustment Natural wideChoose a Corner pattern mode among Red, White, Blue, and Off Settings SettingsBackground Lamp modeLamp control Lamp life control Lamp intervalPicture in Picture Picture in PictureDisplay position setting screen Edge blending Color matchingMeasured information Advanced color matching Test pattern Advanced color matchingHdmi setup Logo Logo and Logo PIN code lock settingsLogo select CaptureChange the Logo PIN code lock setting Logo PIN code lockChange Logo PIN code To enter a Logo PIN code lock To change the Logo PIN codeTo change the code for the remote control Filter controlFan control To change the code for the projectorPower management Direct onKey lock Security Key lock and PIN code lockPIN code lock To change the PIN code lock setting To enter a PIN codeTo change PIN code To change the PIN codeProjector ID ShutterVideo delay control Closed captionFilter counter Appear at turning on and selecting input sourceTimer Factory defaultHow to Overlap the Projection Images on a Screen How To Overlap the Projection ImagesEdge blending How to Overlap the Projection Images Color matchingMaintenance and Care Filter InstructionsMaintenance and Care Reset the filter counter and the scroll counter p.73Service Parts Code 610 335 Replacing the Filter Cartridge Resetting the Scroll Counter Maintenance and Care Resetting the Filter Counter Scroll counter Lamp Management Yellow LampDim Lamp Red LampIndicators Lamp ReplacementLamp 1 / 2 Replace indicators Lamp Handling Precautions Cleaning the Projection Lens Cleaning the Projector CabinetLamp indicator lights on and other indicators blink Then check the matters belowTroubleshooting AppendixAppendix Image is out of focusShutter does not Computer Input/HDMI Input/Video Input Menu TreeComputer Input Image adjust Hdmi Input/Video InputVideo Input Image select ScreenSetting Mode1 OffIndicators Indicators and Projector ConditionProjector is operating normally Projector is detecting abnormal condition Lamp Replace 1If the Filter counter reached a time set in the timer Freq Compatible Computer SpecificationsKHz Svga Supported Signal Format for Optional Board Freq.kHz Freq.HzTechnical Specifications PJ Link Notice Optional PartsProjector Input PJLink Input Parameter Configurations of Terminals Control Port Connector D-sub 9 pinAnalog TERMINALMini D-sub 15 pin USB PORTSeries B Hdmi TERMINAL19 pin Type aPIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Dimensions Unit inch mmList of Picture in Picture Example Serial Control InterfaceFormat Status Read Commands KG2A