NEC 42PD2, 50PD1 user manual Opening the Terminal Board Cover, Attaching the Remote Control Holder

Page 11

Opening the Terminal Board Cover

Slide the knob and at the same time lift the cover.

Knob

Attaching the Remote Control Holder

Insert the top hook of the remote control holder into the installation hole of the main unit and then insert the bot- tom hook into its respective hole.

To remove the remote control holder, first release the bot- tom hook, then release the top hook.

Removing the Terminal Board Cover

This unit’s terminal board cover can be removed. First, open the cover and then:

1.Pull the top hook in the direction of the arrow.

2.Pull the entire terminal board cover downward.

To attach the terminal board cover, insert the bottom hook into the hole, then pull the top hook and insert it into the hole.

Hook

Housing the Remote Control in the Remote Control Holder

First insert the bottom part of the remote control and con- tinue to push it in until the top part clicks into place.

To remove, lift the remote control up from the top part and remove it from the holder.

Image 11

Contents User’s Manual Important Information PrecautionsTo avoid damage and prolong operating life Mises en garde et précautions de sécurité PrécautionsDOC avis de conformation Remarque What is Covered and What is not Covered Limited Warranty Plasma MonitorsContents Pulling Out and Reinserting the Retractable Feet Ventilation Requirements for en- closure mountingIntroduction to the PlasmaSync 42PD2/50PD1 Features you’ll enjoy includeContents of the Package IntroductionConnect the equipment Setup ProcedureRemoving the Terminal Board Cover Attaching the Remote Control HolderHousing the Remote Control in the Remote Control Holder Opening the Terminal Board CoverFront View Part Names and FunctionsRemote Mini jack AC in connectorSide View.... Terminal Board L/R 11 RGB3 DVI 29pinRemote Controller Raster Normal button Remote control transmitterBattery Installation and Replacement Visual Normal buttonOperating Range Using the wired remote control modeDIP Switch Functions and Settings Making the DIP Switch SettingsMode Power Management FunctionPower Management Modes Wiring Diagram InstallationConnections with Equipment that has a Digital Interface Connecting Your PC or Macintosh ComputerConnecting Your VCR DVD or Laser Disc Player Connecting Your Document CameraDaisy-chaining Your monitors When using the Video inputsWhen using the RGB2 Input General Controls PowerAdjustment of the Display OperationAdjustment display of the left/right position Adjustment of the Display DirectAbout to Preset Raster Press Adjustment of the screen display positionAbout to Preset Visual Press Adjustment of the ImageList of Setting Details Adjustment of the DisplayMenu ControlSettings Before Making Adjustments Automatic Storage About to Reset PressPress the Visual Normal button or Raster Normal button Return to the main menu Adjustment of the Image Visual ControlsBrightness Contrast Sharpness Color Tint GAMMA2 Align the cursor with iconAlign the cursor with the desired item Adjustment of Screen Position HorizontalPosition Width Position Height Adjustment of Screen Position VerticalAlign the cursor with Color Temp and set with the / buttons Color Temperature Color TempColor Temp Color Temp High LOW UserGain White Level Bias Black Level Adjustment of the White BalanceOSM H-POS OSM V-POS OSM Angle OSM Display Time Adjustment of the On-screen Display PositionExiting the adjustment OSM H-POS OSM V-POS OSM Angle OSM Display Time Seconds Setting the On-screen Display OFF TimeNormal RGB Mode StillAdjustment of the Clock Frequency/Clock Phase Input Mode 4 X 3 / 16 XClock phase adjustment Fine Picture RGB ModePOL.NEG POL.POS ALL Visual Normal ALL Raster Normal ALL NormalSource Info RGB1 Information Screen Source Info Video Mode NtscWhen RGB input is selected Source RGB1, RGB2, RGB3 When video input is selectedPresent Time SET Timer OFFTimer Screen Direct Daily Weekly SET Timer on Press Proceed for Program MenuProgram Menu Date on OFF Mode Auto Timer ScreenCursor movement Align the cursor with icon 12 on the second Setting Position DriverSetting Position Driver NO.1 Multiple ScreensPress the / buttons and set Other Setting ScreensColor System Align the cursor with icon 13 of the secondBurning reduction function RGB3 ADJ ALL ResetGray Level SET ID no 256 SET noID Selection Screen Symptom Checks Remedy TroubleshootingPlasmaSync 42PD2 Model PX-42VP2A SpecificationsPlasmaSync 50PD1 Model PX-50VP1A Appendix Signal Identification For Raster PresetRGB Connections ApplicationCommunication Format Communication ParametersPage Page Page Page Page Page Page Page Page Cabinet dimensions Unit inchmm