NEC 42PD2, 50PD1, 50PD1, 42PD2 user manual RGB Mode, Clock phase adjustment Fine Picture

Page 37

*RGB MODE:

RGB MODE is displayed at the time of RGB input, RGB MODE is not displayed at the time of video input.

Initial value : STILL

At time of RGB input

[MOTION]: Set when a scan converter or other mov-

 

ing picture has been connected

[STILL]:

Set when displaying a personal computer

 

screen

[DTV]:

Set when using digital broadcast or other

 

sources with an RGB input

This is used in signal discrimination at the time of RGB input.

Note: When a moving picture is displayed in still picture mode, the screen will appear blurry.

4.Make the various adjustments with the POSITION CONTROL ◀ / ♣ buttons.

*Clock frequency adjustment (Picture ADJ)

Adjust the clock frequency and adjust the width of the image with respect to the screen.

The adjustment is made with a dot unit signal. Adjust to the position at which vertical flickering disappears.

POSITION / CONTROL

*WIDE MODE: NORMAL/FULL/STADIUM/ZOOM (Initial value:

NORMAL)

Note that only NORMAL/FULL area available in RGB mode.

Selecting Native Resolutions for 848 x 480, 852 x 480 and 640 x 480 input signals

There are two controls in the Plasma monitor OSM menus that allow you to set the monitor to display resolutions with 848, 852 and 640 horizontal dots in their true resolutions.

When inputting an 848 x 480 signal, align the cursor at the Bottom of the OSM window. Move the cursor down to WIDE MODE and use the POSITION LEFT/RIGHT control to select NORMAL. The monitor will display the signal at 848 x 480. If FULL is selected, the monitor will automatically expand the input signal to 853 x 480.

To choose between 640 x 480 and 852 x 480 resolutions align the cursor with icon 6 (auto) at the top of the OSM window, move the cursor down to INPUT MODE and...

Use the POSITION LEFT/RIGHT control to select 16 x 9 to display 852 x 480 in true resolution or to expand (stretch) 640 x 480 to fill the screen from left to right. Select 4 x 3 to display 640 x 480 resolution in its standard 4:3 aspect ratio with vertical letterbox bars to the right and left of the image.

After selecting the desired setting, go to the Auto menu, set auto picture to OFF and use the Picture Adjust and Fine Picture controls to adjust clock phase and frequency to sharpen the image, if necessary.

When image width is wide (i.e.,

When image width is narrow

clock frequency is high), narrow

(i.e., clock frequency is low),

the width with the (-) button.

widen the width with the (+)

 

button.

 

 

Screen display range

 

 

 

 

Image range width

Go to operation 2 when continuing the adjustment

* Clock phase adjustment (Fine Picture)

Adjust the phase of the clock and adjust the (+) and (-) buttons so that screen noise, flicker, and color infidelity are minimized. First adjust the clock frequency, then perform the clock phase adjustment.

Note: Neither the clock frequency adjustment nor the clock phase adjustment function are available at the time of VIDEO and S-VIDEO input.

5.Return to the main menu

EXIT

*To reset the adjustment value, press the RASTER NORMAL button before pressing the EXIT button.

*To delete the main menu, press the EXIT button once more.

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents User’s Manual Important Information PrecautionsTo avoid damage and prolong operating life DOC avis de conformation PrécautionsMises en garde et précautions de sécurité Remarque What is Covered and What is not Covered Limited Warranty Plasma MonitorsContents Pulling Out and Reinserting the Retractable Feet Ventilation Requirements for en- closure mountingContents of the Package Features you’ll enjoy includeIntroduction Introduction to the PlasmaSync 42PD2/50PD1Connect the equipment Setup ProcedureHousing the Remote Control in the Remote Control Holder Attaching the Remote Control HolderOpening the Terminal Board Cover Removing the Terminal Board CoverFront View Part Names and FunctionsSide View.... Terminal Board L/R AC in connector11 RGB3 DVI 29pin Remote Mini jackRemote Controller Battery Installation and Replacement Remote control transmitterVisual Normal button Raster Normal buttonOperating Range Using the wired remote control modeDIP Switch Functions and Settings Making the DIP Switch SettingsPower Management Modes Power Management FunctionMode Wiring Diagram InstallationConnecting Your VCR DVD or Laser Disc Player Connecting Your PC or Macintosh ComputerConnecting Your Document Camera Connections with Equipment that has a Digital InterfaceWhen using the RGB2 Input When using the Video inputsDaisy-chaining Your monitors Adjustment of the Display PowerOperation General ControlsAbout to Preset Raster Press Adjustment of the Display DirectAdjustment of the screen display position Adjustment display of the left/right positionAbout to Preset Visual Press Adjustment of the ImageList of Setting Details Adjustment of the DisplayMenu ControlSettings Before Making Adjustments Press the Visual Normal button or Raster Normal button About to Reset PressAutomatic Storage Brightness Contrast Sharpness Color Tint GAMMA2 Adjustment of the Image Visual ControlsAlign the cursor with icon Return to the main menuPosition Width Adjustment of Screen Position HorizontalAlign the cursor with the desired item Position Height Adjustment of Screen Position VerticalColor Temp Color Temperature Color TempColor Temp High LOW User Align the cursor with Color Temp and set with the / buttonsGain White Level Bias Black Level Adjustment of the White BalanceExiting the adjustment Adjustment of the On-screen Display PositionOSM H-POS OSM V-POS OSM Angle OSM Display Time OSM H-POS OSM V-POS OSM Angle OSM Display Time Seconds Setting the On-screen Display OFF TimeAdjustment of the Clock Frequency/Clock Phase RGB Mode StillInput Mode 4 X 3 / 16 X NormalClock phase adjustment Fine Picture RGB ModeSource Info RGB1 ALL Visual Normal ALL Raster Normal ALL NormalPOL.NEG POL.POS When RGB input is selected Source RGB1, RGB2, RGB3 Source Info Video Mode NtscWhen video input is selected Information ScreenTimer Screen SET Timer OFFPresent Time Program Menu Date on OFF Mode SET Timer on Press Proceed for Program MenuAuto Timer Screen Direct Daily WeeklyCursor movement Setting Position Driver NO.1 Setting Position DriverMultiple Screens Align the cursor with icon 12 on the secondColor System Other Setting ScreensAlign the cursor with icon 13 of the second Press the / buttons and setGray Level SET ID no RGB3 ADJ ALL ResetBurning reduction function ID Selection Screen SET no256 Symptom Checks Remedy TroubleshootingPlasmaSync 42PD2 Model PX-42VP2A SpecificationsPlasmaSync 50PD1 Model PX-50VP1A Appendix Signal Identification For Raster PresetRGB Connections ApplicationCommunication Format Communication ParametersPage Page Page Page Page Page Page Page Page Cabinet dimensions Unit inchmm
Top Page Image Contents