NEC 50PD1, 42PD2, 42PD2, 50PD1 user manual Application, Connections

Page 52

Function and Pin Configuration of the External Control Connector

Application

These specifications are applicable to NEC plasma monitors (including 42- and 50-inch types) and communications con- trol from external equipment.

Connections

Connections should be made as described below.

External equipment e.g., Personal computer

PDP1

Display PDP2

Display PDP3

Display PDP4

Display

*A maximum of 4 units can used with a cascade connection.

1) Display-side connector: EXTERNAL CONTROL connector

	EXTERNAL CONTROL						Pin No.	Function	Open	Established
	5		4	3	2	1	1 to 3	Not used
							4	Power ON/OFF	ON	OFF
	10		9	8	7	6
							5 and 14	Input switching
	15	14		13	12	11
								The input mode is switched by the combination of pin num-

								bers 5 and 14.

		Input	Pin No. 5	Pin No. 14
		VIDEO	Open	Open
		RGB1	Ground	Open
		RGB2	Open	Ground
		RGB3	Ground	Ground

6 to 8	Not used
9 and 10	Ground
11	TXD (RS-232C)
12	RTS
13	RXD (RS-232C)
15	CTS

2)External equipment side connector: Serial port (RS-232C) connector

See the specifications of the connected equipment for information about the type of connector and pin assignment.

52

Image 52

Contents User’s Manual Precautions Important InformationTo avoid damage and prolong operating life DOC avis de conformation PrécautionsMises en garde et précautions de sécurité Remarque Limited Warranty Plasma Monitors What is Covered and What is not CoveredContents Ventilation Requirements for en- closure mounting Pulling Out and Reinserting the Retractable FeetFeatures you’ll enjoy include Contents of the PackageIntroduction Introduction to the PlasmaSync 42PD2/50PD1Setup Procedure Connect the equipmentAttaching the Remote Control Holder Housing the Remote Control in the Remote Control HolderOpening the Terminal Board Cover Removing the Terminal Board CoverPart Names and Functions Front ViewAC in connector Side View.... Terminal Board L/R11 RGB3 DVI 29pin Remote Mini jackRemote Controller Remote control transmitter Battery Installation and ReplacementVisual Normal button Raster Normal buttonUsing the wired remote control mode Operating RangeMaking the DIP Switch Settings DIP Switch Functions and SettingsPower Management Modes Power Management FunctionMode Installation Wiring DiagramConnecting Your PC or Macintosh Computer Connecting Your VCR DVD or Laser Disc PlayerConnecting Your Document Camera Connections with Equipment that has a Digital InterfaceWhen using the RGB2 Input When using the Video inputsDaisy-chaining Your monitors Power Adjustment of the DisplayOperation General ControlsAdjustment of the Display Direct About to Preset Raster PressAdjustment of the screen display position Adjustment display of the left/right positionAdjustment of the Image About to Preset Visual PressAdjustment of the DisplayMenu Control List of Setting DetailsSettings Before Making Adjustments Press the Visual Normal button or Raster Normal button About to Reset PressAutomatic Storage Adjustment of the Image Visual Controls Brightness Contrast Sharpness Color Tint GAMMA2Align the cursor with icon Return to the main menuPosition Width Adjustment of Screen Position HorizontalAlign the cursor with the desired item Adjustment of Screen Position Vertical Position HeightColor Temperature Color Temp Color TempColor Temp High LOW User Align the cursor with Color Temp and set with the / buttonsAdjustment of the White Balance Gain White Level Bias Black LevelExiting the adjustment Adjustment of the On-screen Display PositionOSM H-POS OSM V-POS OSM Angle OSM Display Time Setting the On-screen Display OFF Time OSM H-POS OSM V-POS OSM Angle OSM Display Time SecondsRGB Mode Still Adjustment of the Clock Frequency/Clock PhaseInput Mode 4 X 3 / 16 X NormalRGB Mode Clock phase adjustment Fine PictureSource Info RGB1 ALL Visual Normal ALL Raster Normal ALL NormalPOL.NEG POL.POS Source Info Video Mode Ntsc When RGB input is selected Source RGB1, RGB2, RGB3When video input is selected Information ScreenTimer Screen SET Timer OFFPresent Time SET Timer on Press Proceed for Program Menu Program Menu Date on OFF ModeAuto Timer Screen Direct Daily WeeklyCursor movement Setting Position Driver Setting Position Driver NO.1Multiple Screens Align the cursor with icon 12 on the secondOther Setting Screens Color SystemAlign the cursor with icon 13 of the second Press the / buttons and setGray Level SET ID no RGB3 ADJ ALL ResetBurning reduction function ID Selection Screen SET no256 Troubleshooting Symptom Checks RemedySpecifications PlasmaSync 42PD2 Model PX-42VP2APlasmaSync 50PD1 Model PX-50VP1A Signal Identification For Raster Preset AppendixRGB Application ConnectionsCommunication Parameters Communication FormatPage Page Page Page Page Page Page Page Page Cabinet dimensions Unit inchmm