NEC 50PD1, 42PD2, 42PD2, 50PD1 Operation, Power, General Controls, Adjustment of the Display

Page 22

Operation

Power

The main unit enters the standby mode when the AC cable is plugged in.

This section describes how to select a computer or video source and how to adjust the picture.

General Controls

Before you turn on your plasma monitor ensure that the computer or video source is turned on.

1)To adjust:

1.Turn On The Monitor

The power button is on the front panel of the monitor. By turning this switch on, the POWER/STANDBY indicator will turn to green and the monitor will become ready to use. OSM is also usable from the front panel.

After you press the POWER OFF button on the remote control, the monitor will go into its standby mode and the POWER/STANDBY indicator will glow orange.

NOTE: The monitor is set to the standby mode when the power cord is plugged in.

2.Select The Computer Or Video Source

Press the “VIDEO” or “RGB 1” “RGB 2” or “RGB 3”(computer) button on the remote control to display the image. Or press the button on the front panel to select your video source: “VIDEO”, “RGB 1”, “RGB 2” or “RGB 3”.

NOTE 1: In the U.S.A. the standard video signal format is NTSC, therefore make sure that the AUTO or NTSC is selected on OSM system control menu. See page 41.

NOTE 2: Select the over scan mode for VIDEO display.

When the RGB input is used, the mode of the power management function can only be in the off state.

In the absence of TMDS signal input, the unit will be in the off state.

(The DVI standard DMPM Active-off power state is equivalent to this.)

The picture will be projected about 4 seconds after the TMDS signal input returns.

3.Adjust The Raster or The Picture Control.

You can adjust the raster such as the horizontal size, vertical size and the brightness and contrast of the image with the remote control.

4.Turning Off The monitor.

Press the POWER OFF button on the remote control or press the POWER button on the front panel.

Adjustment of the Display

There are two methods of adjusting the screen/image using the remote control. One way is direct adjustment by pressing the various buttons and displaying the desired adjustment screens. The other way is to select the menu and display the adjustment screen. This is the menu control adjustment.

When Using the Power Management Function

This unit is designed for use with power management function of the VESA DPMS and DVI DMPM system. When connected with a personal computer or other equipment incorporating the power management software, power consumption is reduced while the monitor is not being used. During power management operation, the STANDBY/POWER lamp changes color to orange or yellow.

*The fan may stop during power management operation. This does not indicate a failure.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents User’s Manual Precautions Important InformationTo avoid damage and prolong operating life DOC avis de conformation PrécautionsMises en garde et précautions de sécurité Remarque Limited Warranty Plasma Monitors What is Covered and What is not CoveredContents Ventilation Requirements for en- closure mounting Pulling Out and Reinserting the Retractable FeetIntroduction Features you’ll enjoy includeContents of the Package Introduction to the PlasmaSync 42PD2/50PD1Setup Procedure Connect the equipmentOpening the Terminal Board Cover Attaching the Remote Control HolderHousing the Remote Control in the Remote Control Holder Removing the Terminal Board CoverPart Names and Functions Front View11 RGB3 DVI 29pin AC in connectorSide View.... Terminal Board L/R Remote Mini jackRemote Controller Visual Normal button Remote control transmitterBattery Installation and Replacement Raster Normal buttonUsing the wired remote control mode Operating RangeMaking the DIP Switch Settings DIP Switch Functions and SettingsPower Management Modes Power Management FunctionMode Installation Wiring DiagramConnecting Your Document Camera Connecting Your PC or Macintosh ComputerConnecting Your VCR DVD or Laser Disc Player Connections with Equipment that has a Digital InterfaceWhen using the RGB2 Input When using the Video inputsDaisy-chaining Your monitors Operation PowerAdjustment of the Display General ControlsAdjustment of the screen display position Adjustment of the Display DirectAbout to Preset Raster Press Adjustment display of the left/right positionAdjustment of the Image About to Preset Visual PressAdjustment of the DisplayMenu Control List of Setting DetailsSettings Before Making Adjustments Press the Visual Normal button or Raster Normal button About to Reset PressAutomatic Storage Align the cursor with icon Adjustment of the Image Visual ControlsBrightness Contrast Sharpness Color Tint GAMMA2 Return to the main menuPosition Width Adjustment of Screen Position HorizontalAlign the cursor with the desired item Adjustment of Screen Position Vertical Position HeightColor Temp High LOW User Color Temperature Color TempColor Temp Align the cursor with Color Temp and set with the / buttonsAdjustment of the White Balance Gain White Level Bias Black LevelExiting the adjustment Adjustment of the On-screen Display PositionOSM H-POS OSM V-POS OSM Angle OSM Display Time Setting the On-screen Display OFF Time OSM H-POS OSM V-POS OSM Angle OSM Display Time SecondsInput Mode 4 X 3 / 16 X RGB Mode StillAdjustment of the Clock Frequency/Clock Phase NormalRGB Mode Clock phase adjustment Fine PictureSource Info RGB1 ALL Visual Normal ALL Raster Normal ALL NormalPOL.NEG POL.POS When video input is selected Source Info Video Mode NtscWhen RGB input is selected Source RGB1, RGB2, RGB3 Information ScreenTimer Screen SET Timer OFFPresent Time Auto Timer Screen SET Timer on Press Proceed for Program MenuProgram Menu Date on OFF Mode Direct Daily WeeklyCursor movement Multiple Screens Setting Position DriverSetting Position Driver NO.1 Align the cursor with icon 12 on the secondAlign the cursor with icon 13 of the second Other Setting ScreensColor System Press the / buttons and setGray Level SET ID no RGB3 ADJ ALL ResetBurning reduction function ID Selection Screen SET no256 Troubleshooting Symptom Checks RemedySpecifications PlasmaSync 42PD2 Model PX-42VP2APlasmaSync 50PD1 Model PX-50VP1A Signal Identification For Raster Preset AppendixRGB Application ConnectionsCommunication Parameters Communication FormatPage Page Page Page Page Page Page Page Page Cabinet dimensions Unit inchmm
Top Page Image Contents