NEC 50PD1, 42PD2, 42PD2, 50PD1 user manual Present Time, SET Timer OFF, Timer Screen

Page 40

Timer Screen

This sets the date and time.

1.Align the cursor with icon (11) of the second page.

The cursor is moved left and right with the POSITION CONTROL◀ / ♣ buttons.

Icon (11)

PRESENT TIME

DATE : 1999. DEC 10

TIME : 22 : 30

SET

TIMER : OFF

2.Use the ▲ / ▼ buttons to move to each of the year, month, day, hour, and minute positions, and the ◀ / ♣ buttons to set the numbers.

PRESENT TIME

DATE : 1999. DEC 10

TIME : 22 : 30

SET

TIMER : OFF

3.Align the cursor with SET and press PROCEED

PROCEED

*When the timer has been set, the LED will flash orange every 3 seconds during remote control standby.

Note: Data can be maintained for about one month by the built-in lithium battery even when the AC cable is disconnected.

POSITION / CONTROL

Cursor moves in the reverse direction

Numbers go				Number go UP

DOWN

Cursor moves in ordered direction

Setting range of date and time settings

Year: 1999 to 2099, Month: JAN to DEC, Day: 01 to 31

Hours: 00 to 24, Minutes: 00 to 59

Image 40

Contents User’s Manual Precautions Important InformationTo avoid damage and prolong operating life DOC avis de conformation PrécautionsMises en garde et précautions de sécurité Remarque Limited Warranty Plasma Monitors What is Covered and What is not CoveredContents Ventilation Requirements for en- closure mounting Pulling Out and Reinserting the Retractable FeetFeatures you’ll enjoy include Contents of the PackageIntroduction Introduction to the PlasmaSync 42PD2/50PD1Setup Procedure Connect the equipmentAttaching the Remote Control Holder Housing the Remote Control in the Remote Control HolderOpening the Terminal Board Cover Removing the Terminal Board CoverPart Names and Functions Front ViewAC in connector Side View.... Terminal Board L/R11 RGB3 DVI 29pin Remote Mini jackRemote Controller Remote control transmitter Battery Installation and ReplacementVisual Normal button Raster Normal buttonUsing the wired remote control mode Operating RangeMaking the DIP Switch Settings DIP Switch Functions and SettingsPower Management Modes Power Management FunctionMode Installation Wiring DiagramConnecting Your PC or Macintosh Computer Connecting Your VCR DVD or Laser Disc PlayerConnecting Your Document Camera Connections with Equipment that has a Digital InterfaceWhen using the RGB2 Input When using the Video inputsDaisy-chaining Your monitors Power Adjustment of the DisplayOperation General ControlsAdjustment of the Display Direct About to Preset Raster PressAdjustment of the screen display position Adjustment display of the left/right positionAdjustment of the Image About to Preset Visual PressAdjustment of the DisplayMenu Control List of Setting DetailsSettings Before Making Adjustments Press the Visual Normal button or Raster Normal button About to Reset PressAutomatic Storage Adjustment of the Image Visual Controls Brightness Contrast Sharpness Color Tint GAMMA2Align the cursor with icon Return to the main menuPosition Width Adjustment of Screen Position HorizontalAlign the cursor with the desired item Adjustment of Screen Position Vertical Position HeightColor Temperature Color Temp Color TempColor Temp High LOW User Align the cursor with Color Temp and set with the / buttonsAdjustment of the White Balance Gain White Level Bias Black LevelExiting the adjustment Adjustment of the On-screen Display PositionOSM H-POS OSM V-POS OSM Angle OSM Display Time Setting the On-screen Display OFF Time OSM H-POS OSM V-POS OSM Angle OSM Display Time SecondsRGB Mode Still Adjustment of the Clock Frequency/Clock PhaseInput Mode 4 X 3 / 16 X NormalRGB Mode Clock phase adjustment Fine PictureSource Info RGB1 ALL Visual Normal ALL Raster Normal ALL NormalPOL.NEG POL.POS Source Info Video Mode Ntsc When RGB input is selected Source RGB1, RGB2, RGB3When video input is selected Information ScreenTimer Screen SET Timer OFFPresent Time SET Timer on Press Proceed for Program Menu Program Menu Date on OFF ModeAuto Timer Screen Direct Daily WeeklyCursor movement Setting Position Driver Setting Position Driver NO.1Multiple Screens Align the cursor with icon 12 on the secondOther Setting Screens Color SystemAlign the cursor with icon 13 of the second Press the / buttons and setGray Level SET ID no RGB3 ADJ ALL ResetBurning reduction function ID Selection Screen SET no256 Troubleshooting Symptom Checks RemedySpecifications PlasmaSync 42PD2 Model PX-42VP2APlasmaSync 50PD1 Model PX-50VP1A Signal Identification For Raster Preset AppendixRGB Application ConnectionsCommunication Parameters Communication FormatPage Page Page Page Page Page Page Page Page Cabinet dimensions Unit inchmm