Lexmark 2500 manual United States Government Rights, Trademarks

Page 76

Notices

76

UNITED STATES GOVERNMENT RIGHTS

This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.

Trademarks

Lexmark and Lexmark with diamond design, ExecJet, and Proprinter are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.

Personal Printer Series is a trademark of Lexmark International, Inc.

ITC Avant Garde Gothic is a trademark or registered trademark of International Typeface Corporation. All other trademarks are the property of their respective owners.

Conventions

Note: A Note identifies something that could help you.

Warning—Potential Damage: A Warning identifies something that could damage your product hardware or software.

CAUTION—POTENTIAL INJURY: A CAUTION identifies something that could cause you harm.

CAUTION—DO NOT TOUCH: This type of CAUTION indicates that you should not touch the marked area.

CAUTION—HOT SURFACE: This type of CAUTION indicates a hot surface.

CAUTION—SHOCK HAZARD: This type of CAUTION indicates a shock hazard.

CAUTION—TIPPING HAZARD: This type of CAUTION indicates a tipping hazard.

Federal Communications Commission (FCC) compliance information statement

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult your point of purchase or service representative for additional suggestions.

Page 75 Page 77
Image 76
Page 75 Page 77
Contents Users Guide JanuaryContents Understanding Setup mode and menu options Administrative supportPaper and specialty media guide Changing tractor positionsTroubleshooting Solving paper feed problemsIndex Safety information Learning about the printer Printer overviewPrinter front view Part nameApplying control panel overlays Printer back viewUnderstanding the printer features and functions Feature/function 2580/2581 2590/2591Feature/function All models Printing a demonstration EANPrinting a network setup Printing from Windows or DOS Using IBM emulation modeWindows Using Epson emulation mode For Lexmark Forms Printer 2580/2581 usersFor Lexmark Forms Printer 2590/2591 users For Forms Printer 2580/2581 usersUsing Okidata Microline emulation mode For Forms Printer 2590/2591 usersUnderstanding the control panel buttons Using the control panelButton Function Understanding the control panel lights Advancing paper Setting the printer online or offlineLight Light status What it means Selecting a Tractor mode Using the Load/Unload functionLocking and unlocking the control panel Selecting and locking a font Disabling Font LockSelecting and locking a pitch Disabling Pitch LockSetting the forms thickness lever Loading paperPaper paths Paper paths for the push tractorSetting the Tear Off position Using the Tear Off functionPaper paths for the pull tractor Loading continuous forms using the push tractor Loading continuous paperPage Page Front loading continuous forms using the pull tractor Page Page Bottom loading continuous forms using the pull tractor Page Page Page Page Loading cut forms Loading a cut form or envelope manuallyLeft paper guide Cut form or envelope Right paper guide Aligning the left margin Setting Top-of-Form Setting Top‑Of‑Form for continuous forms in push modeSetting Top‑Of‑Form for continuous forms in pull mode Setting Top‑Of‑Form for a cut form or an envelopeSetting Top‑Of‑Form in a macro Paper types and sizes supported by the printer Paper and specialty media guidePaper types Single Multiple part Envelopes Push tractor position Changing tractor positionsPull tractor position Converting the push tractor to pull tractor position Converting the pull tractor to push tractor position Page Using Setup mode Understanding Setup mode and menu optionsTo Select Press Changing menu settings an example Control Options Current PressSetup Mode Main menu Main menu optionsForms Macro Options Data OptionsForms Macro options Paper Handling Options Data optionsBuffer Control options Paper Out Alarm Uni‑Dir PrintingAuto Ready Cut Sheet Demo PrintIBM mode Epson modeOKI mode Emulation optionsInterface Selection Honor InitCleaning the printer Maintaining the printerOrdering supplies Removing the ribbon cartridgeCleaning the outside of the printer Recycling Lexmark productsAdministrative support Restoring the factory default settingsRestoring the US factory default settings Restoring the EU factory default settingsSupporting IPSec Supporting SNMPv3Using 802.1x authentication Click Certificate ManagementTroubleshooting Testing the printerChecking an unresponsive printer Running a printer testChecking the printer status Using Hex Trace modeControl panel lights Status Action required Make sure the Tractor 2 option is installed correctly. For Adjusting character bidirectional alignment Solving printing problems Printer is noisy Printer alarm soundsPrinter sounds like it is printing, but does not print Printer power switch is on, but the power light is off Left margin moves to the right during printingIncorrect line length lines do not start at the left margin Printer speed slowsSolving paper feed problems Printing continues beyond the edges of the continuous formsSelected font or pitch is not printing or is changing Paper is jammed in the printerPaper jam in the Tractor 2 Feeder Paper is jammed in the Auto Sheet FeederPrinter does not feed paper Printer does not feed from the Auto Sheet Feeder Printer does not feed from the optional Tractor 2 FeederAuto Sheet Feeder feeds paper at an incorrect rate Paper fed from the Auto Sheet Feeder is skewed Auto Sheet Feeder feeds multiple sheetsPrint is too light Solving print quality problemsDots are missing or print quality is poor Characters are wrong or missing Forms are smudged or print is too darkIncorrect number of lines on a Graphics do not printContacting Customer Support Incorrect line spacing or overprinting occursEdition notice Product name Machine type Model numberUnited States Government Rights TrademarksIndustry Canada compliance statement Avis de conformité aux normes de l’industrie du CanadaEuropean Community EC directives conformity Noise emission levelsPower consumption Mode Description Power consumption WattsStatement of Limited Warranty Power SaverLimited warranty service Limitation of liability Index Numerics
Related manuals
Manual 83 pages 4.68 Kb
Top Page Image Contents