Fujitsu XG2600 manual Connecting a Setup PC, Necessary Hardware / Software, Connect RS232C Cable

Page 50

XG2600 Hardware Guide	Chapter 2 Installation

2.4Connecting a Setup PC

This is to connect a set up PC to the console port of the switch using RS232C cable.

Necessary Hardware / Software

Please prepare the hardware & software specified below to connect to the switch.

•Personal Computer

1 unit of personal computer for setting up configuration is required.

•RS232C cable (Cross, D-SUB9 pin)

RS232C cable is required to connect the set up PC to the switch.

Also, please use the console cable which is included in this product for connection.

Reference User’s Guide "1.1.5 Console Port Specifications" (pg.28)

•Communication Software Terminal software is required.

Connect RS232C Cable

1.Confirm power of both the PC and the switch are off.

2.Connect the RS232C cable and the console cable which is included in this product, and firmly fix them with the screw.

3.Plug in the RJ45 plug of the console cable to the console port of the switch.

Precautions

Please use cross cable for RS232C cable.

50	Connecting a Setup PC

Image 50

Contents XG2600 Xxxx-xxxx-xxxxPreface Contents Connecting a Setup PC About This Manual About the SymbolsOrganization and Usage of This Manual Target Readers and Required KnowledgeProduct name Description in this manual Trademark Notification in This ManualAbbreviated Product Names How the Manuals for This Device Are Organized Manual Name DescriptionAbout Warning Descriptions Safety PrecautionsSymbols Definitions If you notice abnormal conditions such as Failure to follow this may cause damage to Precautions for Use Ensuring SecurityHigh safety CleaningSafety Static electricityLaser safety About Our Green ProductsXG2600 Hardware Guide Chapter Getting Started Parts List Items in the Package / Names and FunctionsCD-ROM Switch Fan Unit Side LED DetailsLED Functions/Behaviors LED Name Light StatusSwitch Interface Side SR/10GBASE-LRPrecautions FDX LEDSFP+ LINK/ACT Top Surface How to attach Cable Holder Cable Restraints with Tyraps Attach Cable Holder to the switch firstOption 1 SFP+ ModuleInstall ation Temperature and Humidity Requirements Requirements for Installation EnvironmentInstallation Requirements Power RequirementsCheck-list Installation RequirementsSpace Requirements Check Item Check ResultRear-Access Configuration Factory Default Installation of the switchDecide Switch Access Configuration Slot 1/Slot PSU2 Slot PSU1 SlotIntake Side Fan Unit SideFront-Access Configuration User Configured Airflow ExhaustDecide positions of rack mounting brackets Rear-Access Configuration Factory DefaultDecide positions for rack mounting brackets Install the switch in a 19 rack Fix rack mounting rails to the rack postsM6 Machine Screws Change the direction of fans to adjust airflow Remove rack mounting bracketsChange direction of fans Loosen two screws to remove fan unitRemove fans Fix fans Remove screws and take off PSU units on the Interface Side XG2600 Hardware Guide Installation Attach rack mounting brackets to the switch Connecting the Equipment Discharging Twisted Pair CableCleaning of Optical Connector Cleaning SFP+ Module / Optical ConnectorCleaning of SFP+ Module Blow dust away with cleanly dry air or nitrogenRemoval of Micro Dust Connecting Twisted Pair Cable / SFP+ Module Connecting Twisted Pair CableConnecting SFP+ Module Type Core/Cladding Diameter Make the replacing SFP+ slot to the disable statusReplacing SFP+ Module Cable Length m# online ether port Plug in the USB Memory Check and confirm that USB port is in a disable statusPlugging in the USB Memory Replacing the USB Memory UnplugConnect RS232C Cable Connecting a Setup PCNecessary Hardware / Software Turn on the Power # clear logging errorSetup Items Prepare a Setup PCPress Return key or Enter key Precautions Confirm # is shown on screen Time Setting コマンドSet up IP address Command When connecting through10GBASE-R SFP+ portIndex Flash LEDXG2600 Hardware Guide Index XG2600 Hardware Guide