Belkin F1DA116PEA, F1DA108PEA, F1DA104PEA Single PRO2 PS/2 Installation, Connect the Console

Page 12

section

			Installation
	1	Your PRO2 PS/2 is now mounted securely into the bracket and you

		are ready to connect cables to the back of the unit.
	2	are ready to connect cables to the back of the unit.
	2	Single PRO2 PS/2 Installation

3This section provides complete instructions for the hardware setup of a single PRO2 PS/2. (F1DA104Pea, F1DA108Pea, and F1DA116Pea) PS/2 Installation: Keyboard, Video, and Mouse Connections

4Connect the Console:

1.Connect the monitor to

5 the PRO2 PS/2. Attach

your monitor cable to the

6HDDB15 female port on the back of the PRO2 PS/2

7

labeled “Console VGA”.

2. Connect the PS/2 keyboard

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

8

cable to the keyboard port

on the back of the PRO2

PS/2 in the “Console”

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

9

section.

3. Connect the PS/2 mouse

10

cable to the mouse port on

the back of the PRO2 PS/2

in the “Console” section.

Attach the power supply to the DC power jack labeled “DC 12V, 1A” located on the rear of the PRO2 PS/2. Once the power is connected to a power source, the LED for port 01 will begin flashing. Sequentially push the direct-access port selectors for ports 01 through 08 (04 for F1DA104Pea and 16 for F1DA116Pea). The corresponding LED should flash as each button is pressed, indicating that the port is ready for connecting your servers (computer connection).

10

Image 12

Contents PRO2 PS/2 Table of Contents Package Contents OverviewOverview Front-Panel Push Button LED DisplaySeven-Segment LED Display Equipment Requirements CablesOmniView All-In-One PRO Series Plus KeyboardsMice MonitorSide View of the PRO2 PS/2 Front View of the PRO2 PS/2 Back View of the PRO2 PS/2Max. Resolution 2048x1536@85Hz Bandwidth 400MHz Port LED IndicatorsDimensions WeightInstallation Pre-Configuration Where to Place the PRO2 PS/2Cable Distance Requirements Installation Step-by-Step Installation GuideSingle PRO2 PS/2 Installation Connect the ConsoleConnect the Computer Connecting Multiple PRO2 PS/2s Daisy-Chaining Bank DIP Switch Configuration Chart ExampleConnecting the Master Switch to the First Slave Switch Before You BeginAdding Additional Slave Units Example of Daisy-Chain Configuration Connecting the ComputersUsing your PRO2 PS/2 Powering up the SystemsUsing your PRO2 PS/2 Selecting a Computer Using Keyboard Hot Key CommandsAutoScan Mode Selecting a Computer Using Direct-Access Port SelectorsBank Up and Bank Down Scroll Buttons Keyboard Hot Key Commands On-Screen Display Menu Control To update the firmware, you will need the following items AutoScan TimeOSD Display Time Updating FirmwareConnecting Computers Setting the PRO2 PS/2 into Flash ModeDIP Switch Firmware Belkin KVM switches and accessories OmniView KVM SwitchesBelkin KVM switches and accessories OmniView All-In-One KVM Cables PRO2 PS/2 series FAQs PRO2 PS/2 series FAQs PRO2 PS/2 series FAQs Troubleshooting Am getting a black screen on my monitorTroubleshooting Mouse Mouse is lost when I switch to a different portMouse is not detected at boot-up Computer boots up, but the mouse does not workWarranty, FCC, CE, Ices Statement Belkin Components Limited Three-Year Product WarrantyFCC Statement F1DA104P, F1DA108P, F1DA116PWarranty, FCC, CE, Ices Statement Belkin GmbH