Belkin F1DA116PEA, F1DA108PEA Connecting Computers, Setting the PRO2 PS/2 into Flash Mode

Page 24

section

1

2

3

4

5

6

7

8

9

10

Using your PRO2 PS/2

Connecting Computers:

1.Connect a keyboard, monitor, and mouse to the computer you prepared for firmware update. It must run Windows 95, 98, or Me.

2.Connect the power adapter to the PRO2 PS/2. Be sure that all connected computers are powered off at this moment.

3.Connect the flash cable.

Setting the PRO2 PS/2 into Flash Mode:

The PRO2 PS/2 has four Flash DIP switches:

	DIP Switch				Firmware
1	2	3	4
ON	OFF	OFF	OFF		Main
OFF	ON	OFF	OFF		OSD
ON	ON	OFF	OFF		Keyboard 1
OFF	OFF	ON	OFF		Mouse 1
ON	OFF	ON	OFF	(F1DA116Pea Only)	Keyboard 2
OFF	ON	ON	OFF	(F1DA116Pea Only)	Mouse 2

The DIP switch should be set to the specified settings when you are

attempting to update a particular firmware. For example, set DIP switch 1 to “ON” to flash update the main firmware of the switch.

Note: F1DA116P requires that you flash update two firmwares for the mouse and keyboard, separately.

1.Once the above steps have been completed, run the Flash software executable. Make sure that the appropriate Flash DIP switch is set to the “on” position. Only one firmware can be flashed at one time.

2.After the Flash update has been completed unplug the power supply from the PRO2 PS/2.

3.Set all DIP switches to the Off position.

4.You are now ready to use your PRO2 PS/2 or continue flashing a different component if necessary.

22

Image 24

Contents PRO2 PS/2 Table of Contents Package Contents OverviewOverview Front-Panel Push Button LED DisplaySeven-Segment LED Display Equipment Requirements CablesOmniView All-In-One PRO Series Plus KeyboardsMice MonitorSide View of the PRO2 PS/2 Front View of the PRO2 PS/2 Back View of the PRO2 PS/2Max. Resolution 2048x1536@85Hz Bandwidth 400MHz Port LED IndicatorsDimensions WeightInstallation Pre-Configuration Where to Place the PRO2 PS/2Cable Distance Requirements Installation Step-by-Step Installation GuideSingle PRO2 PS/2 Installation Connect the ConsoleConnect the Computer Connecting Multiple PRO2 PS/2s Daisy-Chaining Bank DIP Switch Configuration Chart ExampleConnecting the Master Switch to the First Slave Switch Before You BeginAdding Additional Slave Units Example of Daisy-Chain Configuration Connecting the ComputersUsing your PRO2 PS/2 Powering up the SystemsUsing your PRO2 PS/2 Selecting a Computer Using Keyboard Hot Key CommandsAutoScan Mode Selecting a Computer Using Direct-Access Port SelectorsBank Up and Bank Down Scroll Buttons Keyboard Hot Key Commands On-Screen Display Menu Control To update the firmware, you will need the following items AutoScan TimeOSD Display Time Updating FirmwareConnecting Computers Setting the PRO2 PS/2 into Flash ModeDIP Switch Firmware Belkin KVM switches and accessories OmniView KVM SwitchesBelkin KVM switches and accessories OmniView All-In-One KVM Cables PRO2 PS/2 series FAQs PRO2 PS/2 series FAQs PRO2 PS/2 series FAQs Troubleshooting Am getting a black screen on my monitorTroubleshooting Mouse Mouse is lost when I switch to a different portMouse is not detected at boot-up Computer boots up, but the mouse does not workWarranty, FCC, CE, Ices Statement Belkin Components Limited Three-Year Product WarrantyFCC Statement F1DA104P, F1DA108P, F1DA116PWarranty, FCC, CE, Ices Statement Belkin GmbH