SATO LM408/412E manual Unpacking & Parts Identification

Page 17

Unit 3: Installation

UNPACKING & PARTS IDENTIFICATION

Unpack the printer as directed in the following procedure.

1 Place the shipping container (box) upright on a soid, flat surface.

2Open the box, remove any loose items and the first layer of packing material.

3Carefully lift the printer and accessories from the box and place them on a solid flat surface.

4Remove the plastic covers from the packed items and visually inspect for physical damage.

5Ensure all components are present as dictated on the Packing List.

6Report damaged property.

Compact Disc

Power Cord

Packing Cushions

Printer

Protective Sheet

Corrugated Box

Figure 3-1, Unpacking & Parts Identification

LM408-412e Operator Manual

3-2

PN: 9001155A

Image 17

Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationOffset MaintenanceAppendix Introduction Equipment Damage About this Manual1a, Primary Components General DescriptDipswitches Definition Control FeaturesOperator Panel Features LED Definition Operator Panel Technical Data Power Physical CharacteristicsEnvironmental ProcessingSensing CommandMedia RibbonCharacter Font Capabilities UPC A/E Barcode CapabiltiesMSI PostnetInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationCable Connection Printer InstallationSite Location Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading Continuous Mode Operational Mode SelectionTEAR-OFF Mode Accessories Installation unit for guidance Interface SpecificationsInterface Selection RS232C HIGH-SPEED Serial InterfaceOFF ON/X-OFF PIN Direction Signal DefinitionOFF ODD Even None Host Direction READY/BUSY Cable Requirements DB9Printer ON/X-OFF Cable RequirementsPIN Assignments Signal Direction SpecificationsIEEE1284 Parallel Interface ACKSetting Dipswitch SettingsUniversal Serial BUS USB Local Area Network LAN EthernetSoftware Specifications 802.11G Wireless InterfaceLED Indicator Status Description Switch SettingCable Requirements Interface SignalsALL Interfaces 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration Dipswitch Functions Switch Setting Description Dipswitch SettingsNormal Mode Configuration ModesAdvanced Mode Advanced ModeNo change User Download ModeACK Signal XX.X Service ModeCard Mode Card ModeMotion Mode Move ModeHistory Control Mode History Control ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters Mode10, Test Print Mode Test Print Mode11, Boot Download Mode Boot Download Mode12, Flash Memory Download Mode Flash Memory Download ModeYes Default Setting ModeDSW4 on Power HEX Dump Mode15, Maintenance Mode Maintenance ModeMenu Description Normal Mode TableMenu Definition Tables Advanced Mode Table VoltageThreshold low voltage + high voltage = 12 volts Transitional menu screen to access the Service ModeLanguage options Service Mode Table Operator to the biginning of the Card Mode Is only a transitional menu screen for the Service ModeIs only a transitional menu screen to access the Move Mode Transitional menu screen to access the Move ModeHas been removed for application Determined Continuous or Tear-OffWithout pause for application Transitional menu screen to access the Counters Mode Counters Mode TableConfiguration The printer’s configuration settings Is the initial screen of the Test Print ModeBarcode The printer’s installed barcodes Font The contents of the installed fontsTo proceed to the Factory Mode Maintenance Mode Table Troubleshooting Error Signal Troubleshooting Troubleshooting Table Printer Creates a Blank Label No Printed ImageIncorrect Label Positioning Smeared Print ImagesCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface DSW4 on Power Test Print TroubleshootingFeed Test Label PrintingSample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1a, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningDarkness Operational AdjustmentsPotentiometer DESCRIPTION/PROCEDURE Label Print Direction Appendix Print Setup Dimensions Print Setup DimensionsReflective Sensor Label Reference Position3a, Standard Position Label Adjustment DiagramPrinter Connection Diagram 5a, Printer Loading Diagram Printer Loading Diagram5c, Printer Loading Diagram Ascii GlossaryGlossary Being its mating half Bytes Collection of 8 bits used in the binary systemIs a plug male and the other is a socket female Half. The core is convexed and the cavity is concavedDram DPIEeprom Data transmission, seven additional bits are requiredTag would typically have to be removed from its object PowerNext label for printing To attach two or more objectsLED LCDOr voltage divider Primary PotentiometerRF/AIS RAMRF/DC RfidRPM ROMSAM SbplSram Glossary