SATO LM408/412E manual Is the initial screen of the Test Print Mode

Page 57

					Unit 4: Printer Configuration

					TEST PRINT MODE (TABLE 4-10)

	MENU				DESCRIPTION

				Is the initial screen of the Test Print Mode.
				•	CONFIGURATION: The printer’s configuration settings.

	TEST PRINT MODE
	CONFIGURATION			•	BARCODE: The printer’s installed barcodes.
		BARCODE		•	BARCODE: The printer’s installed barcodes.
	HEADCHECK			• HEAD CHECK: A pattern to check print head elements.
		MEMORY		• HEAD CHECK: A pattern to check print head elements.
		MEMORY		•	FONT: The contents of the installed fonts.
		FACTORY		•	FONT: The contents of the installed fonts.
				• FACTORY: A factory test label will be printed.

				This menu screen only appears if CONFIGURATION, BARCODE, or HEAD CHECK was chosen
				in the previous menu. The increments of measure is 1cm.

	TEST PRINT SIZE
	TEST PRINT SIZE
		XXCM


				For factory test prints, this screen appears instead of the previous screen for setting print size.
				Large (10cm) and small (4cm) are the only two options.

	PRINT SIZE
	SMALL	LARGE


				Is a directional screen prompting action on how to terminate print activity. Press FEED to stop
				printing and press again to resume printing.

	PRESS FEED KEY
	PRESS FEED KEY
	TO STOP PRINTING



					BOOT DOWNLOAD MODE (TABLE 4-11)

	MENU				DESCRIPTION

				Is the first menu screen of the Boot Download Mode and provides a prompt to proceed. Pressing
				the FEED key will place the printer in a condition waiting for the data to be received.

	BOOT DOWNLOADER
	BOOT DOWNLOADER
	PRESS FEED KEY


				Is an informational screen only and confirms that the printer is ready to receive the data.


	PROGRAM DOWNLOAD
	READY


				Provides download status that the data is being received and its progression.


	PROGRAM DOWNLOAD
	START > > >	END


				This menu screen appears when all of the data has been received and the process is complete.
				Also prompts the operator on how to proceed.

	DOWNLOAD COMPLETE
	DOWNLOAD COMPLETE
	PRESS FEED KEY

LM408-412e Operator Manual

4-26

PN: 9001155A

Image 57

Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationMaintenance AppendixOffset Introduction Equipment Damage About this Manual1a, Primary Components General DescriptControl Features Operator Panel Features LED DefinitionDipswitches Definition Operator Panel Technical Data Power Physical CharacteristicsEnvironmental ProcessingSensing CommandMedia RibbonCharacter Font Capabilities UPC A/E Barcode CapabiltiesMSI PostnetInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationPrinter Installation Site LocationCable Connection Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading Operational Mode Selection TEAR-OFF ModeContinuous Mode Accessories Installation unit for guidance Interface SpecificationsInterface Selection RS232C HIGH-SPEED Serial InterfacePIN Direction Signal Definition OFF ODD Even NoneOFF ON/X-OFF Host Direction READY/BUSY Cable Requirements DB9Printer ON/X-OFF Cable RequirementsPIN Assignments Signal Direction SpecificationsIEEE1284 Parallel Interface ACKSetting Dipswitch SettingsUniversal Serial BUS USB Local Area Network LAN EthernetSoftware Specifications 802.11G Wireless InterfaceLED Indicator Status Description Switch SettingInterface Signals ALL InterfacesCable Requirements 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration Dipswitch Functions Switch Setting Description Dipswitch SettingsNormal Mode Configuration ModesAdvanced Mode Advanced ModeNo change User Download ModeACK Signal XX.X Service ModeCard Mode Card ModeMotion Mode Move ModeHistory Control Mode History Control ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters Mode10, Test Print Mode Test Print Mode11, Boot Download Mode Boot Download Mode12, Flash Memory Download Mode Flash Memory Download ModeYes Default Setting ModeDSW4 on Power HEX Dump Mode15, Maintenance Mode Maintenance ModeNormal Mode Table Menu Definition TablesMenu Description Advanced Mode Table Transitional menu screen to access the Service Mode Language optionsVoltageThreshold low voltage + high voltage = 12 volts Service Mode Table Operator to the biginning of the Card Mode Is only a transitional menu screen for the Service ModeIs only a transitional menu screen to access the Move Mode Transitional menu screen to access the Move ModeDetermined Continuous or Tear-Off Without pause for applicationHas been removed for application Transitional menu screen to access the Counters Mode Counters Mode TableConfiguration The printer’s configuration settings Is the initial screen of the Test Print ModeBarcode The printer’s installed barcodes Font The contents of the installed fontsTo proceed to the Factory Mode Maintenance Mode Table Troubleshooting Error Signal Troubleshooting Troubleshooting Table Printer Creates a Blank Label No Printed ImageIncorrect Label Positioning Smeared Print ImagesCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface DSW4 on Power Test Print TroubleshootingFeed Test Label PrintingSample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1a, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningOperational Adjustments Potentiometer DESCRIPTION/PROCEDUREDarkness Label Print Direction Appendix Print Setup Dimensions Print Setup DimensionsReflective Sensor Label Reference Position3a, Standard Position Label Adjustment DiagramPrinter Connection Diagram 5a, Printer Loading Diagram Printer Loading Diagram5c, Printer Loading Diagram Glossary GlossaryAscii Being its mating half Bytes Collection of 8 bits used in the binary systemIs a plug male and the other is a socket female Half. The core is convexed and the cavity is concavedDram DPIEeprom Data transmission, seven additional bits are requiredTag would typically have to be removed from its object PowerNext label for printing To attach two or more objectsLED LCDOr voltage divider Primary PotentiometerRF/AIS RAMRF/DC RfidRPM ROMSAM SbplSram Glossary