SATO LM408/412E manual Sensing, Media, Ribbon, Command, Regulatory

Page 13

 

Unit 2: Technical Data

 

 

SENSING

 

 

 

Gap

Adjustable

Reflective Eye-Mark

Adjustable

Ribbon Near End

Enable/Disable

Media Out

Constant

Ribbon Out

Constant

Cover Open

Constant

 

 

MEDIA

 

 

 

Width

Media Width: 0.866 to 5.04 Inches (22-128 mm)

Media Width with Backing Paper: 0.984 to 5.16 Inches (25-131 mm)

 

Length (Continous)

Media Length: 0.237 to 7.01 Inches (6-178 mm)

Media Length with Backing Paper: 0.354 to 7.13 Inches (9-181 mm)

 

Length (Tear-Off)

Media Length: 0.669 to 7.01 Inches (17-178 mm)

Media Length with Backing Paper: 0.787 to 7.13 Inches (20-181 mm)

 

 

Roll or Fan-Fold

Type

Eye-Mark or Gap

 

Direct Thermal or Thermal Transfer

Thickness

0.003 to 0.010 Inches (0.08-0.26 mm)

Roll Diameter

Maximum: 8.6 Inches (218.44 mm)

Core Diameter

3.0 Inches (76.2 mm)

Wind Direction

Face Inward

Fan-Fold Height

Maximum: 3.94 Inches (100 mm)

 

 

RIBBON

 

 

 

Width

Maximum: 4.37 Inches (111 mm)

Length

1476 Feet (450 M)

Wound

Face In

Core Diameter

1 Inch (25.6 mm)

Material

Polyester film

Thickness

(5.8 +/- 0.8 to 8.3 +/- 0.6 ym)

 

 

COMMAND

 

 

 

Standard

SATO Barcode Printer Language (SBPL)

Intelligent Command

 

Non-Standard

N/A

 

 

REGULATORY

 

 

 

Safety

FCC (Class B), EN 55022 (Class B)

 

 

LM408-412e Operator Manual

2-3

PN: 9001155A

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationAppendix MaintenanceOffset Introduction Equipment Damage About this Manual1a, Primary Components General DescriptOperator Panel Features LED Definition Control FeaturesDipswitches Definition Operator Panel Technical Data Power Physical CharacteristicsEnvironmental ProcessingSensing CommandMedia RibbonCharacter Font Capabilities UPC A/E Barcode CapabiltiesMSI PostnetInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationSite Location Printer InstallationCable Connection Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading TEAR-OFF Mode Operational Mode SelectionContinuous Mode Accessories Installation unit for guidance Interface SpecificationsInterface Selection RS232C HIGH-SPEED Serial InterfaceOFF ODD Even None PIN Direction Signal DefinitionOFF ON/X-OFF Host Direction READY/BUSY Cable Requirements DB9Printer ON/X-OFF Cable RequirementsPIN Assignments Signal Direction SpecificationsIEEE1284 Parallel Interface ACKSetting Dipswitch SettingsUniversal Serial BUS USB Local Area Network LAN EthernetSoftware Specifications 802.11G Wireless InterfaceLED Indicator Status Description Switch SettingALL Interfaces Interface SignalsCable Requirements 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration Dipswitch Functions Switch Setting Description Dipswitch SettingsNormal Mode Configuration ModesAdvanced Mode Advanced ModeNo change User Download ModeACK Signal XX.X Service ModeCard Mode Card ModeMotion Mode Move ModeHistory Control Mode History Control ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters Mode10, Test Print Mode Test Print Mode11, Boot Download Mode Boot Download Mode12, Flash Memory Download Mode Flash Memory Download ModeYes Default Setting ModeDSW4 on Power HEX Dump Mode15, Maintenance Mode Maintenance ModeMenu Definition Tables Normal Mode TableMenu Description Advanced Mode Table Language options Transitional menu screen to access the Service ModeVoltageThreshold low voltage + high voltage = 12 volts Service Mode Table Operator to the biginning of the Card Mode Is only a transitional menu screen for the Service ModeIs only a transitional menu screen to access the Move Mode Transitional menu screen to access the Move ModeWithout pause for application Determined Continuous or Tear-OffHas been removed for application Transitional menu screen to access the Counters Mode Counters Mode TableConfiguration The printer’s configuration settings Is the initial screen of the Test Print ModeBarcode The printer’s installed barcodes Font The contents of the installed fontsTo proceed to the Factory Mode Maintenance Mode Table Troubleshooting Error Signal Troubleshooting Troubleshooting Table Printer Creates a Blank Label No Printed ImageIncorrect Label Positioning Smeared Print ImagesCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface DSW4 on Power Test Print TroubleshootingFeed Test Label PrintingSample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1a, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningPotentiometer DESCRIPTION/PROCEDURE Operational AdjustmentsDarkness Label Print Direction Appendix Print Setup Dimensions Print Setup DimensionsReflective Sensor Label Reference Position3a, Standard Position Label Adjustment DiagramPrinter Connection Diagram 5a, Printer Loading Diagram Printer Loading Diagram5c, Printer Loading Diagram Glossary GlossaryAscii Being its mating half Bytes Collection of 8 bits used in the binary systemIs a plug male and the other is a socket female Half. The core is convexed and the cavity is concavedDram DPIEeprom Data transmission, seven additional bits are requiredTag would typically have to be removed from its object PowerNext label for printing To attach two or more objectsLED LCDOr voltage divider Primary PotentiometerRF/AIS RAMRF/DC RfidRPM ROMSAM SbplSram Glossary
Top Page Image Contents