SATO LM408/412E Universal Serial BUS USB, Local Area Network LAN Ethernet, Dipswitch Settings

Page 26

Unit 3: Installation

UNIVERSAL SERIAL BUS (USB)

The Universal Serial Bus (USB) interface is a Plug-In Interface Module that can be installed by the user. It requires a driver (shipped with each printer that has the interface installed) that must be loaded onto the PC and configured to support USB peripherals using Windows 2000 or above. Details for loading the USB driver are contained in the USB Interface Manual that is shipped with each printer with a USB Optional interface installed. Up to 127 devices may be connected to a USB port using powered hubs.

ATTENTION: This Interface type Is not compatible with Windows 98 or Windows Me.

 

SPECIFICATIONS

 

 

Printer Connector

USB Type B Plug

 

 

Cable

10 feet (3 m) maximum

 

 

Host

Windows 2000 or above with USB Port

 

 

Power Supply

BUS Power through cable

 

 

Power Consumption

+5 V at 80 ma

 

 

LOCAL AREA NETWORK (LAN) ETHERNET

A Local Area Network (LAN) interface is an optional Plug-In Interface Module that can be installed by the user. It requires a driver shipped with each printer that has the interface installed. The driver that must be loaded onto the host computer and configured to run one of the supported network protocols using a 10Base-T or 100Base-TX LAN connection. Details for loading the LAN driver are contained in the LAN Interface Manual that is shipped with each printer with a LAN Optional interface installed.

 

SPECIFICATIONS

 

 

Connector

RJ-45 Receptacle

 

 

Cable

10/100BaseT Category 5

 

 

Cable Length

100 meters or less

 

 

Power Supply

Powered from printer

 

 

Protocol

Status3 return

 

Protocol for Driver (cyclic response mode)

 

Protocol for Driver (ENQ response mode)

 

Status5 return

IP Address

0.0.0.0 to 255.255.255.255

 

 

Subnet Mask

0.0.0.0 to 255.255.255.255

 

 

Gateway Address

0.0.0.0 to 255.255.255.255

 

 

 

DIPSWITCH SETTINGS

 

 

SWITCH

SETTING

 

 

1

Reserved (setup prohibited).

2

LAN board EEPROM initialization (configuration).

3

Print configuration details on a label.

4

Print a self-diagmosis of the board onto a label.

 

 

LM408-412e Operator Manual

3-11

PN: 9001155A

Image 26
Contents Printer Sato America, Inc Table of Contents Printer Configuration TroubleshootingOffset MaintenanceAppendix Introduction About this Manual Equipment DamageGeneral Descript 1a, Primary ComponentsDipswitches Definition Control FeaturesOperator Panel Features LED Definition Operator Panel Technical Data Environmental Physical CharacteristicsPower ProcessingMedia CommandSensing RibbonCharacter Font Capabilities MSI Barcode CapabiltiesUPC A/E PostnetInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationCable Connection Printer InstallationSite Location Media Selection Media & Ribbon Loading3b, Fan-fold Media Loading Continuous Mode Operational Mode SelectionTEAR-OFF Mode Interface Selection Interface SpecificationsAccessories Installation unit for guidance RS232C HIGH-SPEED Serial InterfaceOFF ON/X-OFF PIN Direction Signal DefinitionOFF ODD Even None Printer READY/BUSY Cable Requirements DB9Host Direction ON/X-OFF Cable RequirementsIEEE1284 Parallel Interface SpecificationsPIN Assignments Signal Direction ACKUniversal Serial BUS USB Dipswitch SettingsSetting Local Area Network LAN Ethernet802.11G Wireless Interface Software SpecificationsSwitch Setting LED Indicator Status DescriptionCable Requirements Interface SignalsALL Interfaces Receive Buffer Control 50 of 500 items in the history bufferAccessories Installation Interface InstallationPrinter Configuration Unit 4 Printer Configuration Dipswitch Settings Dipswitch Functions Switch Setting DescriptionConfiguration Modes Normal ModeAdvanced Mode Advanced ModeUser Download Mode No changeService Mode ACK Signal XX.XCard Mode Card ModeMove Mode Motion ModeHistory Control Mode History Control ModeProtocol Initialization Mode DSW7 on Line + Feed + PowerCounters Mode Counters ModeTest Print Mode 10, Test Print ModeBoot Download Mode 11, Boot Download ModeFlash Memory Download Mode 12, Flash Memory Download ModeDefault Setting Mode YesHEX Dump Mode DSW4 on PowerMaintenance Mode 15, Maintenance ModeMenu Description Normal Mode TableMenu Definition Tables Advanced Mode Table VoltageThreshold low voltage + high voltage = 12 volts Transitional menu screen to access the Service ModeLanguage options Service Mode Table Is only a transitional menu screen to access the Move Mode Is only a transitional menu screen for the Service ModeOperator to the biginning of the Card Mode Transitional menu screen to access the Move ModeHas been removed for application Determined Continuous or Tear-OffWithout pause for application Counters Mode Table Transitional menu screen to access the Counters ModeBarcode The printer’s installed barcodes Is the initial screen of the Test Print ModeConfiguration The printer’s configuration settings Font The contents of the installed fontsTo proceed to the Factory Mode Maintenance Mode Table Troubleshooting Error Signal Troubleshooting Troubleshooting Table Incorrect Label Positioning No Printed ImagePrinter Creates a Blank Label Smeared Print ImagesInterface Troubleshooting CHK Troubleshooting StepLAN Ethernet Interface Test Print Troubleshooting DSW4 on PowerTest Label Printing FeedSample Test Label Maintenance Cleaning Procedures PRINTER, Excersize Care to Prevent Print Head DamageReplacement Procedures Print Head Replacement1a, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementAdjustment Procedures Print Head Balance AdjustmentPrint Head Alignment 5a, Print Head AlignmentRibbon Guide Alignment Head Balance and Print Head AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningDarkness Operational AdjustmentsPotentiometer DESCRIPTION/PROCEDURE Label Print Direction Appendix Print Setup Dimensions Print Setup DimensionsLabel Reference Position Reflective SensorLabel Adjustment Diagram 3a, Standard PositionPrinter Connection Diagram Printer Loading Diagram 5a, Printer Loading Diagram5c, Printer Loading Diagram Ascii GlossaryGlossary Is a plug male and the other is a socket female Bytes Collection of 8 bits used in the binary systemBeing its mating half Half. The core is convexed and the cavity is concavedEeprom DPIDram Data transmission, seven additional bits are requiredNext label for printing PowerTag would typically have to be removed from its object To attach two or more objectsLCD LEDPotentiometer Or voltage divider PrimaryRF/DC RAMRF/AIS RfidSAM ROMRPM SbplSram Glossary