SATO LM408/412E manual Operational Mode Selection, TEAR-OFF Mode, Continuous Mode

Page 21

Unit 3: Installation

OPERATIONAL MODE SELECTION

There are two modes of printer operation; Dispense and Continuous. The difference between the two is the way that the label and paper backing is ejected. Before printer configuration, one must determine which mode will be used. This chapter identifies the funtional defferences between the two.

TEAR-OFF MODE

With this method of operation, after printing, the printer feeds the first (outermost) label so that it is fully extended out of the printer’s front for dispensing. Printing of the next label will not begin until the prior printed label has been removed. This mode of operation is specifically suited for emmediate application at the time of print.

Upon removal of the prior printed label, the printer repositions the media so that the next label in line may be printed, then prints. The before-mentioned cycle, repeats for each consecutive label.

Printer configuration for the backfeed function may be found in the Advanced Mode of the Configuration unit in this manual. Refer to the Table of Contents for the page number.

CONTINUOUS MODE

With this mode of operation, the media remains in position for printing at all times. To do so, means that the previous printed label is only available for removal when one to four addidtional labels have been printed (quantity is depended on label size). This mode of operation is specifically suited for printing bulk quantities to be applied later.

Printer configuration for the Continuous mode of operation may be found in the Advanced Mode of the Configuration unit in this manual. Refer to the Table of Contents for the page number.

ATTENTION: Refer to the Printer Configuration unit of this manual to program the printer’s internal memory to suit individual needs using the integrated menu options. Refer to the Programming Reference document to remotely program the printer’s features and functions through a host system.

CONTINUOUS MODE

TRANSMISSION SENSOR

REFLECTIVE SENSOR

Base Print Position

TEAR-OFF MODE

TRANSMISSION SENSOR

REFLECTIVE SENSOR

Base Print Position

Base Dispense Position

Base Print &

Dispense Position

LABEL PRINT DIRECTION

Figure 3-4, Label Reference Position

LM408-412e Operator Manual

3-6

PN: 9001155A

Image 21

Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationMaintenance AppendixOffset Introduction Equipment Damage About this Manual1a, Primary Components General DescriptControl Features Operator Panel Features LED DefinitionDipswitches Definition Operator Panel Technical Data Power Physical CharacteristicsEnvironmental ProcessingSensing CommandMedia RibbonCharacter Font Capabilities UPC A/E Barcode CapabiltiesMSI PostnetInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationPrinter Installation Site LocationCable Connection Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading Operational Mode Selection TEAR-OFF ModeContinuous Mode Accessories Installation unit for guidance Interface SpecificationsInterface Selection RS232C HIGH-SPEED Serial InterfacePIN Direction Signal Definition OFF ODD Even NoneOFF ON/X-OFF Host Direction READY/BUSY Cable Requirements DB9Printer ON/X-OFF Cable RequirementsPIN Assignments Signal Direction SpecificationsIEEE1284 Parallel Interface ACKSetting Dipswitch SettingsUniversal Serial BUS USB Local Area Network LAN EthernetSoftware Specifications 802.11G Wireless InterfaceLED Indicator Status Description Switch SettingInterface Signals ALL InterfacesCable Requirements 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration Dipswitch Functions Switch Setting Description Dipswitch SettingsNormal Mode Configuration ModesAdvanced Mode Advanced ModeNo change User Download ModeACK Signal XX.X Service ModeCard Mode Card ModeMotion Mode Move ModeHistory Control Mode History Control ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters Mode10, Test Print Mode Test Print Mode11, Boot Download Mode Boot Download Mode12, Flash Memory Download Mode Flash Memory Download ModeYes Default Setting ModeDSW4 on Power HEX Dump Mode15, Maintenance Mode Maintenance ModeNormal Mode Table Menu Definition TablesMenu Description Advanced Mode Table Transitional menu screen to access the Service Mode Language optionsVoltageThreshold low voltage + high voltage = 12 volts Service Mode Table Operator to the biginning of the Card Mode Is only a transitional menu screen for the Service ModeIs only a transitional menu screen to access the Move Mode Transitional menu screen to access the Move ModeDetermined Continuous or Tear-Off Without pause for applicationHas been removed for application Transitional menu screen to access the Counters Mode Counters Mode TableConfiguration The printer’s configuration settings Is the initial screen of the Test Print ModeBarcode The printer’s installed barcodes Font The contents of the installed fontsTo proceed to the Factory Mode Maintenance Mode Table Troubleshooting Error Signal Troubleshooting Troubleshooting Table Printer Creates a Blank Label No Printed ImageIncorrect Label Positioning Smeared Print ImagesCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface DSW4 on Power Test Print TroubleshootingFeed Test Label PrintingSample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1a, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningOperational Adjustments Potentiometer DESCRIPTION/PROCEDUREDarkness Label Print Direction Appendix Print Setup Dimensions Print Setup DimensionsReflective Sensor Label Reference Position3a, Standard Position Label Adjustment DiagramPrinter Connection Diagram 5a, Printer Loading Diagram Printer Loading Diagram5c, Printer Loading Diagram Glossary GlossaryAscii Being its mating half Bytes Collection of 8 bits used in the binary systemIs a plug male and the other is a socket female Half. The core is convexed and the cavity is concavedDram DPIEeprom Data transmission, seven additional bits are requiredTag would typically have to be removed from its object PowerNext label for printing To attach two or more objectsLED LCDOr voltage divider Primary PotentiometerRF/AIS RAMRF/DC RfidRPM ROMSAM SbplSram Glossary