SATO GT 410, GT 424e, GT408 manual Ribbon, Sensing, Interface Modules

Page 11

Unit 2: Technical Data

MEDIA

 

Media Width: 0.87 to 5.04 Inches (22-128 mm)

Standard Mode

Media Pitch: 0.20 to 5.04 Inches (5-397 mm)

 

 

Backing Paper Width: 0.98 to 5.16 Inches (25-131 mm)

 

 

Backing Paper Pitch: 0.35 to 15.75 Inches (9-400 mm)

 

 

 

Media Width: 0.98 to 5.16 Inches (25-131 mm)

Cutter w/ backfeed

Media Pitch: 0.20 to 5.04 Inches (5-397 mm)

 

 

Backing Paper Width: 0.98 to 5.16 Inches (25-131 mm)

 

 

Backing Paper Pitch:

0.79 to 15.75 Inches (20-400 mm)

 

 

 

Media Width: 0.87 to 5.04 Inches (22-128 mm)

Cutter w/o backfeed

Media Pitch: 0.20 to 5.04 Inches (5-397 mm)

Backing Paper Width: 0.98 to 5.16 Inches (25-131 mm)

 

 

Backing Paper Pitch: 0.35 to 15.75 Inches (9-400 mm)

 

 

 

Media Width: 0.87 to 5.04 Inches (22-128 mm)

Dispenser

Media Pitch: 0.67 to 5.04 Inches (17-397 mm)

 

 

Backing Paper Width: 0.98 to 5.16 Inches (25-131 mm)

 

 

Backing Paper Pitch: 0.79 to 15.75 Inches (20-400 mm)

 

 

 

Media Width: 0.87 to 5.04 Inches (22-128 mm)

Tear-Off

Media Pitch: 0.20 to 5.04 Inches (5-397 mm)

 

 

Backing Paper Width: 0.98 to 5.16 Inches (25-131 mm)

 

 

Backing Paper Pitch:

0.79 to 15.75 Inches (20-400 mm)

 

 

 

RIBBON

 

Minimum:

1.56 Inches (39.5 mm)

Width

 

 

Maximum:

1.77, 2.32, 2.99, 3.31, 3.62, 4.02, 4.37, 5.04

 

 

(45, 59, 76, 84, 92, 102, 111, 128 mm)

 

 

 

Length

492 yards

(450 m) roll.

 

 

Wound

Face In / Face Out. Compatible with coreless paper.

 

 

 

SENSING

Gap

Fixed

 

 

Reflective Eye-Mark

Fixed

 

 

Label

Fixed

 

 

Continuous Form

Sensor not used.

 

 

INTERFACE MODULES

Parallel Port

IEEE 1284 (Communication Mode: ECP/Compatible)

 

 

 

RS232C (9600 to 57,6000 dps) Standard

Serial Port

RS422/485 (9600 to 57600 bps) Optional

Ready/Busy or X-On/X-Off Flow Control

 

 

Bi-Directional Status

 

 

Universal Serial Bus

USB Adapter

 

 

LAN

10BASE-T/100BASE-TX Automatic Switching

 

 

SATO GTxxe Series Operator Manual

PN 9001138A

Page 2-3

Page 10 Page 12
Image 11
Page 10 Page 12
Contents GT408/410/424e Printer Sato America, Inc Table of Contents Maintenance Printer ConfigurationTroubleshooting Introduction Result in Presonal Injury About this Manual1a, Primary Components General DescriptionLCD Display Control FeaturesTechnical Data Processing Physical CharacteristicsPower EnvironmentalInterface Modules RibbonSensing Character Font Capabilities Regulatory Approvals Character ControlBAR Code Capabilties Page Installation Unpacking Unpacking & Parts IdentificationCable Connection Printer InstallationSite Location Media & Ribbon Loading Media Selection3b, Fan-fold Media & Ribbon Loading RS232C Serial Interface RS232C SpecificationsInterface Selection Host Connection DB9 Printer RS232C Serial Interface SignalsPIN Direction Signal Definition Cable Requirements DB9IEEE1284 Parallel Interface SpecificationsLocal Area Network LAN Ethernet 802.11B Wireless802.11B Wireless Specifications Universal Serial BUS USB AdapterACK/NAK Protocol Receive BufferExternal Signal Connector Accessories InstallationPcmcia Memory Expansion Memory ExpansionInterface Upgrade Interface UpgradeLabel Peeler Installation Label Cutter InstallationPrinter Operation Normal Mode Configuration ModesUser Mode User ModeAdvanced Mode Advanced ModeIEEE1284 Interface Setup Mode IEEE1284 Interface Setup ModeRS232C Interface Setup Mode RS232C Interface Setup ModeCentronics Interface Mode Centronics Interface Setup ModeLAN Interface Setup Mode LAN Interface Setup ModeUSB Interface Setup Mode USB Interface Setup ModeCartridge Mode Cartridge Mode10, Sembl Mode Sembl Mode11, Test Print Mode Test Print Mode+ Power Download Mode13, Hex Dump Mode HEX Dump ModeFUNCTION+ + Enter + Power Boot Download Mode15, Data Save Mode Data Save Mode16, Default Settings Mode Default Settings Mode17, Print Cancel Mode Print Cancel Mode18, Print Density Default Mode Print Darkness Default Mode19, Service Mode Service Mode20, Factory Mode Factory ModeMenu Description Normal ModeIs the premiere screen of the Advanced Mode. The Advanced User Mode Print offset refers to the vertical and horizontal shifting Advanced Mode Allows the pitch sensor to be activated or deactivated as Advanced Mode Menu Description Interface Modes 4-4 Through Allows BCC check to be enabled or disabled. Will only appear Allows determination of which method of configuration has OFF with asychronous outputs with Select signal. Will only If any LAN interface is present and the Card option is not Cartridge Mode Sembl Mode Test Print Mode Download Mode HEX Dump Mode Boot Download Mode Data Save Mode Allows selection of data to be initialized Default Settings ModePrint Density Default Mode Print Cancel ModeService Mode Enable or disable the control of ribbon rewind speed Previous printer Confirms copying is in progress. Data entry not required Factory Mode Displays values for the dispenser counter Potentiometer DESCRIPTION/PROCEDURE Operational Adjustments21, Sensor & Accessory Positioning 22, Print Base Reference Position Page Troubleshooting Unit 5 Troubleshooting Alarm sound Three short beeps External signal Machine error Memory Writing error Item Number error Unit 5 Troubleshooting Smeared Print Images Image VoidsLight Print Images Uneven Print DarknessIncorrect Label Positioning Meandering MediaPrinter Creates a Blank Label CHK Troubleshooting Step Interface TroubleshootingLAN Ehternet Interface Hex Dump Mode Test Print TroubleshootingTest Label Printing Test Print ModeSample Test Label Sensor Locations Sensor LocationsMaintenance Cleaning Procedures Print Head Replacement Replacement Procedures1b, Print Head Replacement Platen Roller ReplacementPlaten Roller Replacement Print Head Alignment Adjustment ProceduresPressure Adjustment Media Scale Thickness MM Print Head Pressure AdjustmentBalance Adjustment Print Head Balance AdjustmentRibbon Guide Adjustment Ribbon Guide AdjustmentLabel Sensor Positioning Label Sensor PositioningPotentiometer Adjustments
Top Page Image Contents