Unit 4: Operation
|
|
| INTERFACE MODES | |
|
|
|
| |
| MENU |
| DESCRIPTION | |
|
|
|
|
|
|
|
|
| Allows BCC check to be enabled or disabled. Will only appear |
|
|
|
| when Status5 is set for protocol. |
|
|
|
| |
| BCC CHECK |
|
| |
| ENABLE | DISABLE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Allows selection of the receive buffer type. Select MULTI for |
|
|
|
| multiple buffer and 1ITEM for a single item buffer. Will only |
|
|
|
| |
| RECEIVE BUFFER |
| appear if RS232C, RS422/485, IEEE1284, or Centronics | |
| MULTI | 1ITEM |
| interface is installed unless the card is set for RS232C, RS422/ |
|
|
|
| 485, or Centronics is set for protocol. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Allows setting for ACK width of IEEE1284 interface. Display will |
|
|
|
| appear when the IEEE1284 interface is present and one item is |
|
|
|
| |
| IEEE1284 |
|
| selected as a receive buffer. |
| ACK SIGNAL |
|
| |
|
|
|
| |
|
| 00.5 µs |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Determines whether the print data code requires deletion. |
|
|
|
| Hexadecimal graphic data will not be deleted. Select YES to |
|
|
|
| |
| IGNORE CR/LF |
| delete all carriage return (CR) and line feed (LF) commands in | |
| YES | NO |
| the data stream including graphics and 2D bar codes. |
|
|
|
| This feature is used primarily to maintain compatibility with |
|
|
|
| |
|
|
|
| |
|
|
|
| earlier models of SATO printers. |
|
|
|
|
|
|
|
|
| Allows 1 byte command such as CAN and DLE code to be |
|
|
|
| deleted. Will only appear when the communication protocol is |
|
|
|
| |
| IGNORE CAN/DLE |
| STATUS4 (for overseas precifications). | |
|
|
|
| |
| YES | NO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Allows select of the port to receive print data. CARD1 will |
|
|
|
| receive data sent from the exsting interface and CARD2 will |
|
|
|
| |
| DATA PORT |
|
| receive print data from the Mini LAN. When print data is |
| CARD1 | CARD2 |
| received from a port different from the specified setting, the data |
|
|
|
| will be dleted. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Use this setting to enable or disable the status return port. The |
|
|
|
| interface card which is not being used as the data input port is |
|
|
|
| |
| STATUS PORT |
| ||
|
| the status return port. This selection should be relative to the | ||
|
|
|
| |
| ENABLE | DISABLE |
| setting of the prior menu. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SATO GT4xxe Series Operator Manual | PN 9001138A | Page |