SATO CL408-412e Interface Selection, RS232C HIGH-SPEED Serial Interface, Interface Specifications

Page 23

Unit 3: Installation

INTERFACE SELECTION

This unit presents the printer interface types and their specifications. These specifications include detailed information to assist in the selection of the most appropriate method for the printer to interface with the host. The five acceptable interface methods are:

•RS232C High-Speed Serial

•IEEE1284 Parallel

•Universal Serial Bus (USB)

•Local Area network (LAN) Ethernet

•802.11b Wireless

Following the selection of the desired interface, proceed to the next unit for instructions on how to Configure the printer for that interface type.

WARNING: NEVER CONNECT OR DISCONNECT INTERFACE CABLES (OR USE

A SWITCH BOX) WITH POWER APPLIED TO EITHER THE HOST OR THE

PRINTER. THIS MAY CAUSE DAMAGE TO THE INTERFACE CIRCUITRY IN THE

PRINTER/HOST AND IS NOT COVERED BY WARRANTY.

NOTE: Some hosts monitor the Request-To-Send (RTS) signal (pin 4 of 25) to determine if the printer is ready to receive data. Since the printer does not generate this signal, the RTS line must be held true (high) in order to allow communication. This can be performed by connecting the RTS pin to the Clear-To-Send (CTS) signal (pin 5 of 25).

NOTE: If assistance is required on the physical installation of the interface, refer to the

Accessories Installation unit for guidance.

RS232C HIGH-SPEED SERIAL INTERFACE

This High Speed Serial Interface is a Plug-In Interface Module that can be installed in the printer by the user.

	INTERFACE SPECIFICATIONS

Asynchronous ASCII	Half-duplex communication
	Bi-Directional Communication

Data Transmission Rate	9600, 19200, 38400, 57600 bps

Transmission Form	Start, b1, b2, b3, b4, b5, b6, b7, b8, Stop (b8 will be omitted if using 7 bit oriented)

Data Length	7 or 8 bit (selectable)

Stop Bit	1 or 2 bit (selectable)

Parity Bit	ODD, EVEN, NONE (selectable)

Codes Used	ASC II Character Codes: 7 bits, Graphics: 8 bits

Control Codes	STX (02H), ETX (03H), ACK (06H), NAK (15H)

Connector (Printer Side)	DB-25S Male (equivalent)

Cable Connector	DB-25P Female (equivalent)

Cable Length	5 meters (50ft) or less.

Signal Levels	High = +5V to +12V, Low = -5V to -12V

Protocol	Ready/Busy, X-On/X-Off, Protocol for Driver, Status4 (Bi-Com)

CL408-412e Supplemental Manual

3-8

PN: 9001159A

Image 23

Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationOffset MaintenanceAppendix Introduction Equipment Damage About this Manual1a, Primary Components General DescriptionOperator Panel Features LED Definition Control FeaturesOperator Panel Technical Data Processing Physical CharacteristicsPower EnvironmentalRibbon CommandSensing MediaCharacter Font Capabilities Postnet Barcode CapabiltiesUPC A/E MSIInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationCable Connection Printer InstallationSite Location Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading Continuous Mode Operational Mode SelectionTEAR-OFF Mode Label Print Direction RS232C HIGH-SPEED Serial Interface Interface SpecificationsAccessories Installation unit for guidance Interface SelectionOFF ON/X-OFF PIN Direction Signal DefinitionOFF OFF ODD Even NoneON/X-OFF Cable Requirements READY/BUSY Cable Requirements DB9Host Direction PrinterACK SpecificationsPIN Assignments Signal Direction IEEE1284 Parallel InterfaceLocal Area Network LAN Ethernet Dipswitch SettingsSetting Universal Serial BUS USBDirection Signal Definition Software SpecificationsAccessory EXT Connector PIN Assignments Ssid 802.11G WirelessSwitch Setting LED Indicator Status DescriptionREADY/BUSY Interface Signals EXT Accessory PortWaiting Low 0V when the printer is offline+24V +/- 10% @2A Power for external devices 8b, Timing Chart Repeat Print Cable Requirements Interface SignalsALL Interfaces 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration DSW1 Configuration Dipswitch SettingsDSW1 Default Settings DSW1 Function ConfigurationFunction Description DSW3 Default Settings Normal Mode Configuration ModesAdvanced Mode Advanced ModeUser Download Mode User Download ModeService Mode Service ModeCard Mode Card ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters ModeTest Print Mode Test Print ModeYes Boot Download Mode10, Flash Memory Download Mode Flash Memory Download Mode11, Default Setting Mode Default Setting ModeOnline QTY HEX Dump Mode13, Maintenance Mode Maintenance ModeMenu Description Normal Mode TableAdvanced Mode Table Menu Definition TablesProportional is contemporarily preferred Real-time clock is not installedPoint respectively Stream including graphics and 2D barcodesService Mode Table Operator to manage the expanded memory card As most important where conflicting data existsIs only a transitional menu screen for the Service Mode Languages are provided as optionsCard Mode Table Or use Transitional menu screen to access the Counters ModeAllows the selection of which counter to be viewed to reset Font The contents of the installed fonts Is the initial screen of the Test Print ModeConfiguration The printer’s configuration settings Barcode The printer’s installed barcodesSelect the Interface option for a standard download Also prompts the operator on how to proceedReboot the printer to return to normal operation Clear its Eeprom of all data To proceed to the Factory ModePrint buffer ClearPage. These are the only two options Maintenance Mode TableTroubleshooting Error Signal Troubleshooting Troubleshooting Table Smeared Print Images No Printed ImagePrinter Creates a Blank Label Incorrect Label PositioningCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface Power Test Print TroubleshootingTest Label Printing Sample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1b, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningDarkness Operational AdjustmentsPotentiometer DESCRIPTION/PROCEDURE Print Base Reference Position Appendix Direction Print Setup DimensionsLabel Reference Position Label Reference Position DiagramAscii GlossaryGlossary Half. The core is convexed and the cavity is concaved Bytes Collection of 8 bits used in the binary systemBeing its mating half Is a plug male and the other is a socket femaleData transmission, seven additional bits are required DPIDram EepromTo attach two or more objects PowerTag would typically have to be removed from its object Next label for printingLED LCDOr voltage divider Primary PotentiometerRfid RAMRF/AIS RF/DCSbpl ROMRPM SAMSram Glossary