SATO CL408-412e manual 802.11G Wireless, Switch Setting, LED Indicator Status Description, Ssid

Page 29

Unit 3: Installation

802.11G WIRELESS

The wireless print server provides easy printer interface with 802.11G Wi-Fi compliant networks free of wired connections. Each printer is shipped with an integrated driver and interface installed. The driver must be loaded onto the host computer and configured to run one of the supported protocols.

	SPECIFICATIONS

Variable Data Rates	54, 11, 5.5, 2 and 1 Mbps

Frequency Band	2.4 GHz ISM Band

Wired Equivalent Privacy	128 bit, 64 bit (compatible with 40bit), WPA, none

Sensitivity	(typ, AAWGN, 8E-2 PER): -91dBm at 1Mbps, -88dBm at 2 Mdps, -87dBm at 5.5Mbps, -
	84dBm at 11Mbps.

Range	100m indoors, 300m outdoors

Protocols	TCP/IP, IPX/SPX, Direct Mode IPX/IP, DLC/LLC, NetBEUI, NetBIOS/IP

Protocol	Status3 return
	Protocol for Driver (cyclic response mode)
	Protocol for Driver (ENQ response mode)
	Status5 return

IP Address	0.0.0.0 to 255.255.255.255

Subnet Mask	0.0.0.0 to 255.255.255.255

Gateway Address	0.0.0.0 to 255.255.255.255

Communication Mode	802.11 Ad hoc, Ad hoc, Infrastructure

SSID	Optional alphanumeric character string (up to 32 characters)

Channels	01 to 11

DIPSWITCH SETTINGS

The dipswitches serve to initialize the configuration saved on the Wireless-LAN board, print the configuration, and make a self- diagnosis. To communicate with the host,set the communication mode by through switches 5 and 6, then set the remaining switches to the OFF position.

Print of configuration and self-diagnsis are operable only on the screen after turning on the printer. Ensure all switches are in the OFF position when operating the printer.

SWITCH	SETTING

1	Reserved for test use only (setup prohibited).
2	LAN board EEPROM initialization (initialize configuration).
3	Print configuration details on a label (diagnostic & configuration).
4	Print a self-diagmosis of the board onto a label (wireless mode).

NOTE: The communication mode may be set within the printer’s Interface Mode. Go to [Communication] of the Interface Mode to enable setup by either the dipswitches or through the Interface Mode.

LED INDICATOR STATUS

INDICATOR 1	INDICATOR 2	INDICATOR 3	DESCRIPTION

ON	OFF	OFF	Weak Signal (1-50%)

ON	ON	OFF	Moderate Signal (50-75%)

ON	ON	ON	Strong Signal (75-100%)

OFF	OFF	ON	802.11 Ad hoc

OFF	ON	OFF	Ad hoc

CL408-412e Supplemental Manual

3-14

PN: 9001159A

Image 29

Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationOffset MaintenanceAppendix Introduction Equipment Damage About this Manual1a, Primary Components General DescriptionOperator Panel Features LED Definition Control FeaturesOperator Panel Technical Data Power Physical CharacteristicsEnvironmental ProcessingSensing CommandMedia RibbonCharacter Font Capabilities UPC A/E Barcode CapabiltiesMSI PostnetInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationCable Connection Printer InstallationSite Location Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading Continuous Mode Operational Mode SelectionTEAR-OFF Mode Label Print Direction Accessories Installation unit for guidance Interface SpecificationsInterface Selection RS232C HIGH-SPEED Serial InterfaceOFF PIN Direction Signal DefinitionOFF ODD Even None OFF ON/X-OFFHost Direction READY/BUSY Cable Requirements DB9Printer ON/X-OFF Cable RequirementsPIN Assignments Signal Direction SpecificationsIEEE1284 Parallel Interface ACKSetting Dipswitch SettingsUniversal Serial BUS USB Local Area Network LAN EthernetDirection Signal Definition Software SpecificationsAccessory EXT Connector PIN Assignments Switch Setting 802.11G WirelessLED Indicator Status Description SsidREADY/BUSY Interface Signals EXT Accessory PortWaiting Low 0V when the printer is offline+24V +/- 10% @2A Power for external devices 8b, Timing Chart Repeat Print Cable Requirements Interface SignalsALL Interfaces 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration DSW1 Configuration Dipswitch SettingsDSW1 Default Settings DSW1 Function ConfigurationFunction Description DSW3 Default Settings Normal Mode Configuration ModesAdvanced Mode Advanced ModeUser Download Mode User Download ModeService Mode Service ModeCard Mode Card ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters ModeTest Print Mode Test Print ModeYes Boot Download Mode10, Flash Memory Download Mode Flash Memory Download Mode11, Default Setting Mode Default Setting ModeOnline QTY HEX Dump Mode13, Maintenance Mode Maintenance ModeAdvanced Mode Table Normal Mode TableMenu Definition Tables Menu DescriptionPoint respectively Real-time clock is not installedStream including graphics and 2D barcodes Proportional is contemporarily preferredService Mode Table Is only a transitional menu screen for the Service Mode As most important where conflicting data existsLanguages are provided as options Operator to manage the expanded memory cardCard Mode Table Or use Transitional menu screen to access the Counters ModeAllows the selection of which counter to be viewed to reset Configuration The printer’s configuration settings Is the initial screen of the Test Print ModeBarcode The printer’s installed barcodes Font The contents of the installed fontsSelect the Interface option for a standard download Also prompts the operator on how to proceedReboot the printer to return to normal operation Print buffer To proceed to the Factory ModeClear Clear its Eeprom of all dataPage. These are the only two options Maintenance Mode TableTroubleshooting Error Signal Troubleshooting Troubleshooting Table Printer Creates a Blank Label No Printed ImageIncorrect Label Positioning Smeared Print ImagesCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface Power Test Print TroubleshootingTest Label Printing Sample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1b, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningDarkness Operational AdjustmentsPotentiometer DESCRIPTION/PROCEDURE Print Base Reference Position Appendix Direction Print Setup DimensionsLabel Reference Position Label Reference Position DiagramAscii GlossaryGlossary Being its mating half Bytes Collection of 8 bits used in the binary systemIs a plug male and the other is a socket female Half. The core is convexed and the cavity is concavedDram DPIEeprom Data transmission, seven additional bits are requiredTag would typically have to be removed from its object PowerNext label for printing To attach two or more objectsLED LCDOr voltage divider Primary PotentiometerRF/AIS RAMRF/DC RfidRPM ROMSAM SbplSram Glossary