SATO CL408-412e manual Counters Mode

Page 47

Unit 4: Printer Configuration

COUNTERS MODE

The printer has integrated counters to measure the accumilative activity of some features. The unit of measure is based on linear meters and includes a print head counter and a life counter. The head counter records the length of the media that has been printed since the print head was installed and should be reset each time the print head is replaced.

The life counter meaures the lenght of media the printer as a whole has printed. This counter would only be reset in case circuitry replacement.

The printer’s Counter Mode allows the operator to view the accumilated measurement and also allows the print head counter to be reset to zero.

Use the keys of the printer’s operator panel to select and enter the required options. Refer to the Menu Definition Tables in the following chapter to provide an explanation of each menu screen.

Toggles

Advanced

Mode

Toggles

Card Mode

LINE + POWER

ADVANCED MODE

FEED

LINE

CARD MODE

FEED

LINE

	SERVICE MODE
Toggles
Service	FEED	LINE
Mode

COUNTERS MODE

			Toggles
			Move	LINE			FEED
			Mode
				COUNTERS
				HD	DSP	CUT	LIFE
			Scrolls		LINE
			options		LINE
			options
		HD		HD			HD		Life
		FEED		FEED			FEED		FEED
	HEAD COUNTER		DISPENSE COUNTER			CUT COUNTER			LIFE COUNTER
		X.XM		X.XM				X	X.XM
		FEED		FEED			FEED		FEED
	HEAD COUNTER CLEAR		DSP COUNTER CLEAR			CUT COUNTER CLEAR
	YES	NO	YES	NO			YES	NO
Scrolls	LINE		LINE			LINE
options	LINE	FEED	LINE	FEED		LINE		FEED
options

Figure 4-7, Counters Mode

CL408-412e Supplemental Manual

4-12

PN: 9001159A

Image 47

Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationOffset MaintenanceAppendix Introduction Equipment Damage About this Manual1a, Primary Components General DescriptionOperator Panel Features LED Definition Control FeaturesOperator Panel Technical Data Processing Physical CharacteristicsPower EnvironmentalRibbon CommandSensing MediaCharacter Font Capabilities Postnet Barcode CapabiltiesUPC A/E MSIInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationCable Connection Printer InstallationSite Location Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading Continuous Mode Operational Mode SelectionTEAR-OFF Mode Label Print Direction RS232C HIGH-SPEED Serial Interface Interface SpecificationsAccessories Installation unit for guidance Interface SelectionOFF ON/X-OFF PIN Direction Signal DefinitionOFF OFF ODD Even NoneON/X-OFF Cable Requirements READY/BUSY Cable Requirements DB9Host Direction PrinterACK SpecificationsPIN Assignments Signal Direction IEEE1284 Parallel InterfaceLocal Area Network LAN Ethernet Dipswitch SettingsSetting Universal Serial BUS USBDirection Signal Definition Software SpecificationsAccessory EXT Connector PIN Assignments Ssid 802.11G WirelessSwitch Setting LED Indicator Status DescriptionREADY/BUSY Interface Signals EXT Accessory PortWaiting Low 0V when the printer is offline+24V +/- 10% @2A Power for external devices 8b, Timing Chart Repeat Print Cable Requirements Interface SignalsALL Interfaces 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration DSW1 Configuration Dipswitch SettingsDSW1 Default Settings DSW1 Function ConfigurationFunction Description DSW3 Default Settings Normal Mode Configuration ModesAdvanced Mode Advanced ModeUser Download Mode User Download ModeService Mode Service ModeCard Mode Card ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters ModeTest Print Mode Test Print ModeYes Boot Download Mode10, Flash Memory Download Mode Flash Memory Download Mode11, Default Setting Mode Default Setting ModeOnline QTY HEX Dump Mode13, Maintenance Mode Maintenance ModeMenu Description Normal Mode TableAdvanced Mode Table Menu Definition TablesProportional is contemporarily preferred Real-time clock is not installedPoint respectively Stream including graphics and 2D barcodesService Mode Table Operator to manage the expanded memory card As most important where conflicting data existsIs only a transitional menu screen for the Service Mode Languages are provided as optionsCard Mode Table Or use Transitional menu screen to access the Counters ModeAllows the selection of which counter to be viewed to reset Font The contents of the installed fonts Is the initial screen of the Test Print ModeConfiguration The printer’s configuration settings Barcode The printer’s installed barcodesSelect the Interface option for a standard download Also prompts the operator on how to proceedReboot the printer to return to normal operation Clear its Eeprom of all data To proceed to the Factory ModePrint buffer ClearPage. These are the only two options Maintenance Mode TableTroubleshooting Error Signal Troubleshooting Troubleshooting Table Smeared Print Images No Printed ImagePrinter Creates a Blank Label Incorrect Label PositioningCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface Power Test Print TroubleshootingTest Label Printing Sample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1b, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningDarkness Operational AdjustmentsPotentiometer DESCRIPTION/PROCEDURE Print Base Reference Position Appendix Direction Print Setup DimensionsLabel Reference Position Label Reference Position DiagramAscii GlossaryGlossary Half. The core is convexed and the cavity is concaved Bytes Collection of 8 bits used in the binary systemBeing its mating half Is a plug male and the other is a socket femaleData transmission, seven additional bits are required DPIDram EepromTo attach two or more objects PowerTag would typically have to be removed from its object Next label for printingLED LCDOr voltage divider Primary PotentiometerRfid RAMRF/AIS RF/DCSbpl ROMRPM SAMSram Glossary