SATO CL408-412e manual About this Manual, Equipment Damage

Page 7

Unit 1: Introduction

ABOUT THIS MANUAL

This manual is laid out consistent with the product discussed and provides all of the information required for printer installation and operation by the purchaser.

This manual also incorporates the use of special information boxes. Examples of these boxes and the type of information provided in each, are below.

WARNING: PROVIDES INFORMATION THAT, IF UNHEEDED, MAY RESULT IN

PERSONAL INJURY.

CAUTION: PROVIDES INFORMATION THAT, IF UNHEEDED, MAY RESULT IN

EQUIPMENT DAMAGE.

ATTENTION: Provides information that is deemed of special importance but will not result in personal injury or product damage if unheeded.

NOTE: Provides helpful hints to assist in performing the tasks at hand.

LCD DISPLAY: Provides the specific display that should be visible on the LCD at that point.

A comprehensive Table Of Contents provided at the front of this manual facilitates rapid movement within. The contents identify the different Units, Chapters, and some Sections. Each references the page number of their commencement.

The pages of this manual have embedded headers and footers to assist the user in identifying his or her exact position within the manual. The header provides the unit number followed by its name. The footer identifies the product on the left, the page number in the center, and the manual’s part number to the right side of the page.

Page enumeration is two-part with each separated by a hyphen. The first character set references the Unit and the second identifies the page number within that unit. Page numbers begin with the numeral one (1) at the beginning of a new unit and ascend sequentially.

CL408-412e Supplemental Manual

1-2

PN: 9001159A

Image 7
Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationAppendix MaintenanceOffset Introduction Equipment Damage About this Manual1a, Primary Components General DescriptionOperator Panel Features LED Definition Control FeaturesOperator Panel Technical Data Processing Physical CharacteristicsPower EnvironmentalRibbon CommandSensing MediaCharacter Font Capabilities Postnet Barcode CapabiltiesUPC A/E MSIInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationSite Location Printer InstallationCable Connection Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading TEAR-OFF Mode Operational Mode SelectionContinuous Mode Label Print Direction RS232C HIGH-SPEED Serial Interface Interface SpecificationsAccessories Installation unit for guidance Interface SelectionOFF ON/X-OFF PIN Direction Signal DefinitionOFF OFF ODD Even NoneON/X-OFF Cable Requirements READY/BUSY Cable Requirements DB9Host Direction PrinterACK SpecificationsPIN Assignments Signal Direction IEEE1284 Parallel InterfaceLocal Area Network LAN Ethernet Dipswitch SettingsSetting Universal Serial BUS USBAccessory EXT Connector PIN Assignments Software SpecificationsDirection Signal Definition Ssid 802.11G WirelessSwitch Setting LED Indicator Status DescriptionREADY/BUSY Interface Signals EXT Accessory Port+24V +/- 10% @2A Power for external devices Low 0V when the printer is offlineWaiting 8b, Timing Chart Repeat Print ALL Interfaces Interface SignalsCable Requirements 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration DSW1 Default Settings Dipswitch SettingsDSW1 Configuration Function Description ConfigurationDSW1 Function DSW3 Default Settings Normal Mode Configuration ModesAdvanced Mode Advanced ModeUser Download Mode User Download ModeService Mode Service ModeCard Mode Card ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters ModeTest Print Mode Test Print ModeYes Boot Download Mode10, Flash Memory Download Mode Flash Memory Download Mode11, Default Setting Mode Default Setting ModeOnline QTY HEX Dump Mode13, Maintenance Mode Maintenance ModeMenu Description Normal Mode TableAdvanced Mode Table Menu Definition TablesProportional is contemporarily preferred Real-time clock is not installedPoint respectively Stream including graphics and 2D barcodesService Mode Table Operator to manage the expanded memory card As most important where conflicting data existsIs only a transitional menu screen for the Service Mode Languages are provided as optionsCard Mode Table Allows the selection of which counter to be viewed to reset Transitional menu screen to access the Counters ModeOr use Font The contents of the installed fonts Is the initial screen of the Test Print ModeConfiguration The printer’s configuration settings Barcode The printer’s installed barcodesReboot the printer to return to normal operation Also prompts the operator on how to proceedSelect the Interface option for a standard download Clear its Eeprom of all data To proceed to the Factory ModePrint buffer ClearPage. These are the only two options Maintenance Mode TableTroubleshooting Error Signal Troubleshooting Troubleshooting Table Smeared Print Images No Printed ImagePrinter Creates a Blank Label Incorrect Label PositioningCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface Power Test Print TroubleshootingTest Label Printing Sample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1b, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningPotentiometer DESCRIPTION/PROCEDURE Operational AdjustmentsDarkness Print Base Reference Position Appendix Direction Print Setup DimensionsLabel Reference Position Label Reference Position DiagramGlossary GlossaryAscii Half. The core is convexed and the cavity is concaved Bytes Collection of 8 bits used in the binary systemBeing its mating half Is a plug male and the other is a socket femaleData transmission, seven additional bits are required DPIDram EepromTo attach two or more objects PowerTag would typically have to be removed from its object Next label for printingLED LCDOr voltage divider Primary PotentiometerRfid RAMRF/AIS RF/DCSbpl ROMRPM SAMSram Glossary