SATO CL408-412e manual Waiting, Low 0V when the printer is offline

Page 31

Unit 3: Installation

READY/BUSY INTERFACE SIGNALS

DB-9	14 PIN	DIRECTION	SIGNAL DEFINITION
PIN	CENTRONICS	DIRECTION	SIGNAL DEFINITION

			When Mode1 on the LCD is selected High Voltage = Online Print Job
	9	To Host	Waiting.
	9	To Host	When Mode2 on the LCD is selected High Voltage = Online. This goes

			low (0V) when the printer is offline.

	11		Reserved.

	12	To Host	+24V +/- 10% @2A - Power for external devices.

	14		Frame Ground

NOTE: The signals on pins 1, 3, 4, and 10 each have an open collector output. These pins normally measure +.07V maximum when a true condition exists. If a false condition occurs, the voltage will drop to 0V. To achieve a signal level of +5V, a 330 ohm, 1/4 watt pull-up resistor between the open collector output pin and Vcc (pin 13) as illustrated. This will provide a signal level of +5V for a true condition and 0V when a false condition exists. The maximum voltage that can be applied to these pins is +50V and the maximum current they can sink is 500 milliamps.

Figure 3-7, Signal Diagram

Figure 3-8a, Timing Chart - Standard Operation

CL408-412e Supplemental Manual

3-16

PN: 9001159A

Image 31

Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationAppendix MaintenanceOffset Introduction Equipment Damage About this Manual1a, Primary Components General DescriptionOperator Panel Features LED Definition Control FeaturesOperator Panel Technical Data Processing Physical CharacteristicsPower EnvironmentalRibbon CommandSensing MediaCharacter Font Capabilities Postnet Barcode CapabiltiesUPC A/E MSIInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationSite Location Printer InstallationCable Connection Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading TEAR-OFF Mode Operational Mode SelectionContinuous Mode Label Print Direction RS232C HIGH-SPEED Serial Interface Interface SpecificationsAccessories Installation unit for guidance Interface SelectionOFF ON/X-OFF PIN Direction Signal DefinitionOFF OFF ODD Even NoneON/X-OFF Cable Requirements READY/BUSY Cable Requirements DB9Host Direction PrinterACK SpecificationsPIN Assignments Signal Direction IEEE1284 Parallel InterfaceLocal Area Network LAN Ethernet Dipswitch SettingsSetting Universal Serial BUS USBAccessory EXT Connector PIN Assignments Software SpecificationsDirection Signal Definition Ssid 802.11G WirelessSwitch Setting LED Indicator Status DescriptionREADY/BUSY Interface Signals EXT Accessory Port+24V +/- 10% @2A Power for external devices Low 0V when the printer is offlineWaiting 8b, Timing Chart Repeat Print ALL Interfaces Interface SignalsCable Requirements 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration DSW1 Default Settings Dipswitch SettingsDSW1 Configuration Function Description ConfigurationDSW1 Function DSW3 Default Settings Normal Mode Configuration ModesAdvanced Mode Advanced ModeUser Download Mode User Download ModeService Mode Service ModeCard Mode Card ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters ModeTest Print Mode Test Print ModeYes Boot Download Mode10, Flash Memory Download Mode Flash Memory Download Mode11, Default Setting Mode Default Setting ModeOnline QTY HEX Dump Mode13, Maintenance Mode Maintenance ModeMenu Description Normal Mode TableAdvanced Mode Table Menu Definition TablesProportional is contemporarily preferred Real-time clock is not installedPoint respectively Stream including graphics and 2D barcodesService Mode Table Operator to manage the expanded memory card As most important where conflicting data existsIs only a transitional menu screen for the Service Mode Languages are provided as optionsCard Mode Table Allows the selection of which counter to be viewed to reset Transitional menu screen to access the Counters ModeOr use Font The contents of the installed fonts Is the initial screen of the Test Print ModeConfiguration The printer’s configuration settings Barcode The printer’s installed barcodesReboot the printer to return to normal operation Also prompts the operator on how to proceedSelect the Interface option for a standard download Clear its Eeprom of all data To proceed to the Factory ModePrint buffer ClearPage. These are the only two options Maintenance Mode TableTroubleshooting Error Signal Troubleshooting Troubleshooting Table Smeared Print Images No Printed ImagePrinter Creates a Blank Label Incorrect Label PositioningCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface Power Test Print TroubleshootingTest Label Printing Sample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1b, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningPotentiometer DESCRIPTION/PROCEDURE Operational AdjustmentsDarkness Print Base Reference Position Appendix Direction Print Setup DimensionsLabel Reference Position Label Reference Position DiagramGlossary GlossaryAscii Half. The core is convexed and the cavity is concaved Bytes Collection of 8 bits used in the binary systemBeing its mating half Is a plug male and the other is a socket femaleData transmission, seven additional bits are required DPIDram EepromTo attach two or more objects PowerTag would typically have to be removed from its object Next label for printingLED LCDOr voltage divider Primary PotentiometerRfid RAMRF/AIS RF/DCSbpl ROMRPM SAMSram Glossary