SATO CL408-412e Universal Serial BUS USB, Local Area Network LAN Ethernet, Dipswitch Settings

Page 27

Unit 3: Installation

UNIVERSAL SERIAL BUS (USB)

The Universal Serial Bus (USB) interface is a Plug-In Interface Module that can be installed by the user. It requires a driver (shipped with each printer that has the interface installed) that must be loaded onto the PC and configured to support USB peripherals using Windows 2000 or above. Details for loading the USB driver are contained in the USB Interface Manual that is shipped with each printer with a USB Optional interface installed. Up to 127 devices may be connected to a USB port using powered hubs.

ATTENTION: This Interface type Is not compatible with Windows 98 or Windows Me.

	SPECIFICATIONS

Printer Connector	USB Type B Plug

Cable	10 feet (3 m) maximum

Host	Windows 2000 or above with USB Port

Power Supply	BUS Power through cable

Power Consumption	+5 V at 80 ma

LOCAL AREA NETWORK (LAN) ETHERNET

A Local Area Network (LAN) interface is an optional Plug-In Interface Module that can be installed by the user. It requires a driver shipped with each printer that has the interface installed. The driver that must be loaded onto the host computer and configured to run one of the supported network protocols using a 10Base-T or 100Base-TX LAN connection. Details for loading the LAN driver are contained in the LAN Interface Manual that is shipped with each printer with a LAN Optional interface installed.

	SPECIFICATIONS

Connector	RJ-45 Receptacle

Cable	10/100BaseT Category 5

Cable Length	100 meters or less

Power Supply	Powered from printer

Protocol	Status3 return
	Protocol for Driver (cyclic response mode)
	Protocol for Driver (ENQ response mode)
	Status5 return
IP Address	0.0.0.0 to 255.255.255.255

Subnet Mask	0.0.0.0 to 255.255.255.255

Gateway Address	0.0.0.0 to 255.255.255.255

	DIPSWITCH SETTINGS

SWITCH	SETTING

1	Reserved (setup prohibited).
2	LAN board EEPROM initialization (configuration).
3	Print configuration details on a label.
4	Print a self-diagmosis of the board onto a label.

CL408-412e Supplemental Manual

3-12

PN: 9001159A

Image 27

Contents Printer Sato America, Inc Table of Contents Troubleshooting Printer ConfigurationMaintenance AppendixOffset Introduction Equipment Damage About this Manual1a, Primary Components General DescriptionOperator Panel Features LED Definition Control FeaturesOperator Panel Technical Data Processing Physical CharacteristicsPower EnvironmentalRibbon CommandSensing MediaCharacter Font Capabilities Postnet Barcode CapabiltiesUPC A/E MSIInstallation Unpacking & Parts Identification Unpacking & Parts IdentificationPrinter Installation Site LocationCable Connection Media & Ribbon Loading Media Selection3b, Fan-fold Media Loading Operational Mode Selection TEAR-OFF ModeContinuous Mode Label Print Direction RS232C HIGH-SPEED Serial Interface Interface SpecificationsAccessories Installation unit for guidance Interface SelectionOFF ON/X-OFF PIN Direction Signal DefinitionOFF OFF ODD Even NoneON/X-OFF Cable Requirements READY/BUSY Cable Requirements DB9Host Direction PrinterACK SpecificationsPIN Assignments Signal Direction IEEE1284 Parallel InterfaceLocal Area Network LAN Ethernet Dipswitch SettingsSetting Universal Serial BUS USBSoftware Specifications Accessory EXT Connector PIN AssignmentsDirection Signal Definition Ssid 802.11G WirelessSwitch Setting LED Indicator Status DescriptionREADY/BUSY Interface Signals EXT Accessory PortLow 0V when the printer is offline +24V +/- 10% @2A Power for external devicesWaiting 8b, Timing Chart Repeat Print Interface Signals ALL InterfacesCable Requirements 50 of 500 items in the history buffer Receive Buffer ControlInterface Installation Accessories InstallationPrinter Configuration Unit 4 Printer Configuration Dipswitch Settings DSW1 Default SettingsDSW1 Configuration Configuration Function DescriptionDSW1 Function DSW3 Default Settings Normal Mode Configuration ModesAdvanced Mode Advanced ModeUser Download Mode User Download ModeService Mode Service ModeCard Mode Card ModeDSW7 on Line + Feed + Power Protocol Initialization ModeCounters Mode Counters ModeTest Print Mode Test Print ModeYes Boot Download Mode10, Flash Memory Download Mode Flash Memory Download Mode11, Default Setting Mode Default Setting ModeOnline QTY HEX Dump Mode13, Maintenance Mode Maintenance ModeMenu Description Normal Mode TableAdvanced Mode Table Menu Definition TablesProportional is contemporarily preferred Real-time clock is not installedPoint respectively Stream including graphics and 2D barcodesService Mode Table Operator to manage the expanded memory card As most important where conflicting data existsIs only a transitional menu screen for the Service Mode Languages are provided as optionsCard Mode Table Transitional menu screen to access the Counters Mode Allows the selection of which counter to be viewed to resetOr use Font The contents of the installed fonts Is the initial screen of the Test Print ModeConfiguration The printer’s configuration settings Barcode The printer’s installed barcodesAlso prompts the operator on how to proceed Reboot the printer to return to normal operationSelect the Interface option for a standard download Clear its Eeprom of all data To proceed to the Factory ModePrint buffer ClearPage. These are the only two options Maintenance Mode TableTroubleshooting Error Signal Troubleshooting Troubleshooting Table Smeared Print Images No Printed ImagePrinter Creates a Blank Label Incorrect Label PositioningCHK Troubleshooting Step Interface TroubleshootingLAN Ethernet Interface Power Test Print TroubleshootingTest Label Printing Sample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning ProceduresPrint Head Replacement Replacement Procedures1b, Print Head Replacement Interface Board Replacement Interface Board ReplacementFuse Replacement Fuse ReplacementPrint Head Balance Adjustment Adjustment Procedures5a, Print Head Alignment Print Head AlignmentHead Balance and Print Head Alignment Ribbon Guide AlignmentLabel Sensor Positioning Label Sensor PositioningRibbon Spindle Tensioning Ribbon Spindle TensioningOperational Adjustments Potentiometer DESCRIPTION/PROCEDUREDarkness Print Base Reference Position Appendix Direction Print Setup DimensionsLabel Reference Position Label Reference Position DiagramGlossary GlossaryAscii Half. The core is convexed and the cavity is concaved Bytes Collection of 8 bits used in the binary systemBeing its mating half Is a plug male and the other is a socket femaleData transmission, seven additional bits are required DPIDram EepromTo attach two or more objects PowerTag would typically have to be removed from its object Next label for printingLED LCDOr voltage divider Primary PotentiometerRfid RAMRF/AIS RF/DCSbpl ROMRPM SAMSram Glossary