Fujitsu FP-410 user manual Conditions for Use

Page 19

8.Conditions for Use

(1)High-duty printing might cause blurred printing. Use an appropriate duty that does not cause blurs.

(2)To print an external character set, a bold font (e.g., Gothic) or bold lines should be selected. If a fine font (e.g., Mincho) or fine lines are selected, the print density might be insufficient.

(3)To prevent enlarged or reduced printing due to uneven feeding after cutting paper or stopping printing, the paper must be advanced at least 1 mm (8 dots) before printing resumes.

(4)Characters printed in red or blue of dual-color, thermal paper are less durable.

(5)When dual-color, thermal paper is used, a bold font (e.g., Gothic) should be selected. If a fine font (e.g., Mincho) is selected, the print color might become faint. In this case, the print duty must not exceed 30%. A print duty of greater than 30% might make the black print faint.

(6)Do not use this printer outdoors. Use of this printer outdoors might cause a printer malfunction.

(7)Use only the specified thermal paper. If other non-specified paper is used, the print quality may deteriorate, the thermal print head and cutter life may be shortened, or the printer may fail.

(8)To print on cardboard with a thickness of 90m, set the cutter drive function to the cardboard mode during printer setup. Printing cardboard in the standard cutter drive mode might cause a cutting error.

(9)The Paper Near-End state is only detected if a paper roll with an outside core diameter of 18 mm and 22.2mm is used. If a paper roll with an outside core diameter of 32 mm is used, the paper near-end state is not detected.

(10)When you use 58mm width for long period, a part of head may be worn out because this part has been directly touched on Platen Roller. This may cause the print error. Also, Cutter may be worn out by the same condition as Head, and this may cause Cut Error. When you use 80mm width paper after 58mm width paper used for long period, we recommend you to replace these parts. If you need, please purchase and replace these parts.

18

ENGLISH

Image 19
Contents X0KA02001-Y911-02 USER’S ManualCopyright 2002 Fujitsu Isotec Limited Table of Contents Appearance and Names of Components Interface connector Serial interface Consumable Parts and AC Adapter Roll Paper specification Thermal paperAC adapter option Connecting the Interface Cable Connecting Cables and AC AdapterConnecting the Drawer Kick Cable Connecting the AC Adapter Turning on the Power Control Panel Error IndicationControl Panel Loading the roll paper Loading the Roll PaperPage English Removing the Paper Roll Clearing a Paper Jam Preventing Paper JamsCleaning the Thermal Head Periodic CleaningConditions for Use Page English Inhaltsverzeichni Erscheinung und Teilebezeichnungen Page Wechselstromadapters option Wärmeempfindliches PapierEinzelblatt-Spezifikationen Wärmeempfindliches Papier HinweisAnschließen des Schnittstellenkabels Kabelanschluss an einen WechselstromadapterAnschließen des Einschub-Kick-Kabels Anschließen des Wechselstromadapters Hinweis Einschalten der Stromzufuhr Bedienfeld Anzeigeleuchten und SchalterFehleranzeige Papier einfüllen Papier einfüllenHinweis Hinweise Entfernen der Papierrolle Lösen von Papierstaus Verhindern von PapierstausReinigung des Thermodruckkopfes Periodische ReinigungBenutzungsbedingungen Page Deutsch General Specifications Appendix a SpecificationsAppendix Outline drawingSpecifications of Environmental Conditions Cutter SpecificationsSpecifications of Paper Supply Specifications of InterfacesBlack mark specification Printer with black mark sensor only Specifications of ReliabilityPage Serial Interface Specifications of transmission interfaceOutput Send request Input Data set ready Signal ground UnusedOutput Send data Input Receive dataTXD RXD RTS CTS DSR DTR Forward channel Parallel InterfaceReverse channel USB Interface Type-B Connector 4PinType-A Connector 8Pin Drawer Kick ConnectorDrawer connection Printer 1 Cable Drawer Drawer connection Printer CableAppendix Test Printing Appendix C Special ModesHEX Dump Example of contents of HEX dump test printingSetting up the Printer Power on Status Disable Enable Setup group items Setup items Memory switchMemory Switch setup items Setup ItemsSerial Interface Condition setup items Address your comments and inquiries on this manual to Other setup items