Fujitsu FP-410 USB Interface, Type-B Connector 4Pin, Type-A Connector 8Pin, Drawer Kick Connector

Page 50

B-3. USB Interface

(1) Type-B Connector: 4Pin

Item	Signal Name	I/O direction	Function
1	BUS5V	--	BUS-POWER5V
2	D-inB	In/Out	D-
3	D+inB	In/Out	D+
4	SG1	--	Grand

(2) Type-A Connector: 8Pin

Item	Signal Name	I/O direction	Function
1	USB5V2	Out	+5V for A1
2	D-OUTA2	In/Out	D- for A2
3	D+OUTA2	In/Out	D+ for A3
4	SG1	--	Grand for A4
5	USB5V3	Out	+5V for B1
6	D-OUTA3	In/Out	D- for B2
7	D+OUTA3	In/Out	D+ for B3
8	SG1	--	Grand for B4

Note: The electric power consumption of the device connected with the Type-A connector should be up to 0.1A or less. When the device that exceeds this condition is connected, it would cause the failure of the printer. The USB cable must be a shielded one.

B-4. Drawer Kick Connector

Pin No.

Signal Name

I/O direction

Function

1

DRSNS2

Drawer sense signal 2

Input

2

*DRD1

Drawer kick drive signal 1

Output

3

DRSNS1

Drawer sense signal 1

Input

4

+24V

Drive power

Output

5

*DRD2

Drawer kick drive signal 2

Output

6

SG

Drawer sense ground signal

Output

1

6

Connecting side

49

Image 50

Contents USER’S Manual X0KA02001-Y911-02Copyright 2002 Fujitsu Isotec Limited Table of Contents Appearance and Names of Components Interface connector Serial interface Roll Paper specification Thermal paper Consumable Parts and AC AdapterAC adapter option Connecting Cables and AC Adapter Connecting the Interface CableConnecting the Drawer Kick Cable Connecting the AC Adapter Turning on the Power Control Panel Error IndicationControl Panel Loading the Roll Paper Loading the roll paperPage English Removing the Paper Roll Preventing Paper Jams Clearing a Paper JamPeriodic Cleaning Cleaning the Thermal HeadConditions for Use Page English Inhaltsverzeichni Erscheinung und Teilebezeichnungen Page Hinweis Wärmeempfindliches PapierEinzelblatt-Spezifikationen Wärmeempfindliches Papier Wechselstromadapters optionKabelanschluss an einen Wechselstromadapter Anschließen des SchnittstellenkabelsAnschließen des Einschub-Kick-Kabels Anschließen des Wechselstromadapters Hinweis Einschalten der Stromzufuhr Fehleranzeige Anzeigeleuchten und SchalterBedienfeld Papier einfüllen Papier einfüllenHinweis Hinweise Entfernen der Papierrolle Verhindern von Papierstaus Lösen von PapierstausPeriodische Reinigung Reinigung des ThermodruckkopfesBenutzungsbedingungen Page Deutsch Appendix a Specifications General SpecificationsOutline drawing AppendixSpecifications of Interfaces Cutter SpecificationsSpecifications of Paper Supply Specifications of Environmental ConditionsSpecifications of Reliability Black mark specification Printer with black mark sensor onlyPage Specifications of transmission interface Serial InterfaceInput Receive data Input Data set ready Signal ground UnusedOutput Send data Output Send requestTXD RXD RTS CTS DSR DTR Parallel Interface Forward channelReverse channel Drawer Kick Connector Type-B Connector 4PinType-A Connector 8Pin USB InterfaceDrawer connection Printer 1 Cable Drawer connection Printer Cable DrawerAppendix Appendix C Special Modes Test PrintingExample of contents of HEX dump test printing HEX DumpSetting up the Printer Setup group items Setup items Memory switch Power on Status Disable EnableSetup Items Memory Switch setup itemsSerial Interface Condition setup items Other setup items Address your comments and inquiries on this manual to