Fujitsu Siemens Computers Point 1600, Point 500 manual Wall-Mount Cradle Exploded View

Page 39

7.Route the keyboard cable through the notch on the left side of the keyboard tray assembly as shown in Figure 2-15.

8.Connect the keyboard cable to keyboard port on the cradle module. Ensure that you have connected the keyboard cable to the correct port. The keyboard port is the middle connector on the bottom of the cradle module (closest to the DC input connector).

9.Attach the cradle module to the keyboard tray assembly by installing the two (size #10) screws provided with the wall-mount base in the side of the keyboard tray assembly as shown in Figure

2-15.To allow alignment of other components, do not tighten these screws at this time. Note that the tubular lock on the cradle module (if so equipped) fits through the hole in the front of the keyboard tray assembly. (Ensure that the rubber feet and wire catch, supplied with the cradle module, are not installed on the cradle module.) Store the excess keyboard cable in the keyboard tray assembly housing. Pull the keyboard cable tight on the outside of the keyboard tray assembly to ensure that the keyboard cable will not be pinched by the keyboard tray when it is folded to the closed position. (Apply some duct tape to secure the keyboard cable to the inside of the keyboard tray assembly while you work.)

2 Screws (size #6)

 

Tubular Lock

Keyboard Cable

Notch

 

(for keyboard

 

cable routing)

Velcro

Strips

(for installing FMWKB1-type keyboards)

Cover Label

Cradle Module

AC Adapter

DC Supply Cable

Keyboard Tray Assembly

Housing

2 Screws (size #10)

6 Screws (size #8)

To attach keyboard tray assembly to mounting plate.

Figure 2-15. Wall-Mount Cradle Exploded View

10.Position the AC adapter inside the keyboard tray assembly below the cradle module and connect the DC supply cable to the DC input port on the cradle module. (Tuck the looped excess cable underneath the AC adapter inside the keyboard tray assembly housing. This allows clearance for the AC adapter relative to the contour of the keyboard tray assembly housing.)

Installing the Wall-Mount Cradle

2-23

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Point Page Point Page Canadian DOC Compliance FCC NoticePage Table of Contents Page Organization About This GuideViii About This Guide Connectivity Peripheral Model Numbers Introduction to Connectivity PeripheralsConnectors on Connectivity Peripherals Portable Port Expander Cradle ModuleHigh-Usage Cradle Port ReplicatorHigh-Connectivity Cradle Charge-Only Cradle Wall-Mount CradleAssembling and Installing Connectivity Peripherals Bottom View, Portable Port Expander Portable Port Expander ConnectorsAssembling the Port Replicator Attaching the Feet Port Replicator Back View Bottom View, Port Replicator Port Replicator ConnectorsUsing the Folding Desk Stand Assembling the High-Usage Cradle High-Usage Cradle Assembly High-Usage Cradle Bottom View High-Usage Cradle Connectors Installing the High-Usage Cradle Fastening Cradle Module to Desktop Assembling the High-Connectivity Cradle 10. High-Connectivity Cradle Assembly 11. High-Connectivity Cradle Bottom View Installing the High-Connectivity Cradle High-Connectivity Cradle Connectors Required Tools and Hardware Installing the Wall-Mount CradleAssembling and Installing Connectivity Peripherals 12. Wall-Mount Cradle Mounting Plate 13. Coiling DC Supply Cable 15. Wall-Mount Cradle Exploded View Push Tighten Tighten Push 19. Fastening Cradle Module Left Side 21. Checking Cradle Module Alignment Testing the Wall-Mount Cradle After Installation Wall-Mount Cradle Connectors 23. Charge-Only Cradle Installing the Charge-Only Cradle24. Status Lights on the Pen Tablet Confirming External Power Is SuppliedAssembling and Installing Connectivity Peripherals Index Page Page 58-0627-00A
Top Page Image Contents