Cisco Systems N55M4Q manual Connecting Devices to the Ethernet Ports

Page 33

Chapter 2 Switch Installation

Connecting Devices to the Ethernet Ports

Figure 2-35 Removing a Bale-Clasp Latch SFP Module

5 6 7 8

Catalyst

 

3560-

 

CG

Series

PoE

9

10

208914

1

1

Bale clasp

Connecting Devices to the Ethernet Ports

Connecting to the 10/100 and 10/100/1000 Ports, page 2-33

Connecting to the PoE Ports, page 2-34

Connecting to the 10/100 and 10/100/1000 Ports

The 10/100 and 10/100/1000 Ethernet ports use RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328 feet (100 meters). The 100BASE-TX and 1000BASE-T traffic requires Category 5, Category 5e, or Category 6 UTP cable. The 10BASE-T traffic uses Category 3 or Category 4 cable.

The autonegotiation feature is enabled by default on the switch. At this setting, the switch ports configure themselves to operate at the speed of the attached device. If the device does not support autonegotiation, you can set the switch port speed and duplex parameters. To maximize performance, either let the ports autonegotiate both speed and duplex, or set the port speed and duplex parameters on both ends of the connection.

See the switch software configuration guide or the switch command reference on Cisco.com for more information about autonegotiation and auto-MDIX.

If auto-MDIX is disabled, use the guidelines in Table 2-1to select the cable for connecting the 10/100/1000 Ethernet ports to other devices. See the “Cables and Adapters” section on page B-3for cable-pinout descriptions. See Figure 2-36.

 

 

Catalyst 3560-C and 2960-C Switch Hardware Installation Guide

 

 

 

 

 

 

OL-23803-02

 

 

2-33

 

 

 

 

 

Image 33
Contents Preparing for Installation Switch InstallationStatement Installation Guidelines Powering the Switch Box ContentsEquipment That You Supply Mounting the Switch Verifying Switch OperationOn a Desk or Shelf without Mounting Screws Desk, Shelf, or Wall with Mounting ScrewsDesk- or Shelf-Mounting Installing the Mounting Screws on Top of a Desk or a Shelf Under the Desk- or Shelf-Mounting Mounting the Switch on Top of a Desk or ShelfDesk or shelf Screws Screw template Adhesive Desk or shelf Slides on this way Wall-Mounting77 in .49 cm 72 in .44 cm 46. 62 in .19 cm Switch Installing the Mounting Screws on the Wall Mounting Tray with Screws With a Mounting TraySwitch Mounting tray Sliding direction Desk Mounting Tray with a Magnet 10 Securing the Mounting Tray to the SwitchPlace the switch on the mounting tray. See Figure 13 Wall-Mounting with a Magnet A Rack Attaching Brackets to the Switch15 Attaching the 23-inch Brackets for Rack-Mounting Mounting the Switch in a RackOn a DIN Rail Attaching the DIN-Mount Tray to the Switch18 Securing the DIN-Mount Tray to the Switch Mounting the Switch on a DIN Rail19 Mounting the Switch on a DIN Rail Removing the Switch from a DIN Rail 21 Reset Cover on the Catalyst 2960CPD-8PT-L Switch Installing a Cover for the Reset Button Optional23 Inserting the Retainer through the Lanced Loop Installing the Power Cord Retainer OptionalSlide the retainer through the first latch. See Figure 26 Sleeve Around the Power Cord Washer Installing the Cable Guard Optional29 Attaching the Cable Guard to the Switch 31 Attaching the Cables to the Switch Installing SFP Modules After Installing the SwitchRemoving SFP Modules 34 Installing an SFP ModuleConnecting to the 10/100 and 10/100/1000 Ports Connecting Devices to the Ethernet PortsDevice Crossover Cable Connecting to the PoE PortsWhere to Go Next OL-23803-02
Related manuals
Manual 168 pages 60.68 Kb