Cisco Systems OL-23421-02 manual Installation

Page 18

Chapter 2 Installation

Installation

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of:

140°F (60°C) Statement 1047

Warning This equipment is supplied as “open type” equipment. It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts. The interior of the enclosure must be accessible only by the use of a tool.

The enclosure must meet IP 54 or NEMA type 4 minimum enclosure rating standards. Statement 1063

Warning This equipment is intended to be grounded to comply with emission and immunity requirements. Ensure that the switch functional ground lug is connected to earth ground during normal use. Statement 1064

Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 1.75 in. (4.4 cm) Statement 1076

Installation

Follow these steps to install the switch module:

Step 1 Before you install (or remove) the switch module from the host CGR 2010 router, you must power down the router as described in the “Shutting Off Power” section in Chapter 3 of the Cisco Connected Grid Router 2010 Hardware Installation Guide.

Step 2 Facing the I/O side of the Cisco CGR 2010 router, use a no. 2 Phillips screwdriver to remove the slot divider between the slots where you intend to install the switch module - either slots 0 and 1 or slots 2 and 3 (see Figure 2-1).

a.Remove the two screws on the slot divider.

b.Remove the slot divider and set it aside.

Cisco Connected Grid Ethernet Switch Module Interface Card Getting Started Guide

2-2

OL-23421-02

 

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Cisco Systems, Inc Page N T E N T S Other Management Options Preface PurposeDocument Conventions Obtaining Documentation and Submitting a Service Request Related PublicationsProduct Overview Switch ModelsMode Description GRWIC-D-ES-2S-8PCPorts Port LocationsPort Labeling Port Label10/100BASE-T Ports PoE and PoE+ PortsPort Description 10/100 Mb/s SFP Module Slots 100/1000 Mb/s SFP Module SlotsDual-Purpose Gigabit Ethernet Ports Supported SFPs Type of SFP Module ModelLEDs SYSPoE Router Compact Flash Memory Cards Label on Cisco IOS Router Description Interface Name CF1CF0 Installation Pre-InstallationInstallation Warning Statements Installation Removing the Slot Divider From the CGR 2010 Router Installing the Switch Module in the CGR 2010 Router Connecting to the Network Connecting the Copper Switch ModuleConnecting the Fiber Switch Module Connecting the Copper Model to the NetworkRemoving the Switch Module Connecting the SFP Fiber Model to the NetworkOL-23421-02 Express Setup Express SetupSystem Requirements Recessed Express Setup Button Express Setup Window Field Description Vlan IDTroubleshooting Express Setup Resetting the Switch ModuleProblem Resolution Follow the steps in Express Setup, Managing the Switch Module Using the Device ManagerCisco Configuration Professional Interface IP Address Accessing the Switch ModuleOther Management Options Method Status ProtocolDisconnecting from the Switch Module Command PurposePurpose Connecting Devices to the Switch Module SFP Module Slots 237941 Dual-Purpose Port with RJ-45 and SFP Connectors 237964 Dual-Purpose Connectors Verifying Port ConnectivityOL-23421-02 Cable and Connectors Connector SpecificationsSFP Module Connectors Cables and Adapters Dual-Purpose PortsSFP Module Cables Extended temperature SFPs Core Modal WavelengthCommercial SFPs Cable Pinouts Bandwidth Type of SFP Module Nanometers Fiber TypeMHz/km1 Cable Distance Figure A-6 OL-23421-02
Top Page Image Contents