Cisco Systems OL-23421-02 manual Field Description, Vlan ID

Page 28

Chapter 3 Express Setup

Express Setup

Step 3 Enter the Network Settings values:

Field

Description

 

 

Management Interface

Use the default setting of 1.

(VLAN ID)

Note Enter a new VLAN ID only if you want to change the management

 

 

interface for the switch module. The VLAN ID range is 1 to 1001.

 

 

IP Assignment Mode

Use the default setting of Static, which means that the switch module keeps

 

the IP address.

 

Note Use the DHCP setting when you want the switch module to

 

automatically obtain an IP address from the DHCP server.

 

 

IP Address

Enter the IP address of the switch module

 

 

Subnet Mask

Select a subnet mask from the drop-down

 

 

Default Gateway

Enter the IP address for the default gateway (router)

 

 

Switch Password

Enter your password. The password can be from 1 to 25 alphanumeric

 

characters, can start with a number, is case sensitive, allows embedded

 

spaces, but does not allow spaces at the beginning or end.

 

 

Confirm Switch

Enter your password again

Password

Note You must change the password from the default password cisco.

 

 

 

Step 4 Enter the Optional Settings now, or enter them later using the Device Manager interface.

You can enter other administrative settings in the Express Setup window. For example, the optional administrative settings identify and synchronize the switch module for enhanced management. NTP synchronizes the switch module with the network clock. You can also manually set the system clock settings.

Step 5 Click Submit to save your changes.

The switch module is now configured and exits Express Setup. The browser displays a warning message and attempts to connect with the earlier switch module IP address. Typically, connectivity between the computer and the switch module is lost because the configured switch module IP address is in a different subnet for the computer IP address.

Step 6 Disconnect the switch module from the computer, and install the switch module in your network (see Installation, page 2-2).

Step 7 If you have not changed your IP address, skip this step.

If you changed your IP address in the previous set of steps, change it to the previously configured IP address (see Step 3).

Step 8 Display the Device Manager:

a.Open a web browser and enter the switch module IP address.

b.Enter the username and password and then click Enter.

For more information on configuring and managing the switch module, see Accessing the Switch Module, page 4-2.

Note If the Device Manager does not display, check the following:

•Confirm that the LED for the switch module port connected to your network is green

Cisco Connected Grid Ethernet Switch Module Interface Card Getting Started Guide

3-4

OL-23421-02

 

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Cisco Systems, Inc Page N T E N T S Other Management Options Purpose PrefaceDocument Conventions Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Mode DescriptionProduct Overview GRWIC-D-ES-2S-8PCPorts Port LocationsPort Labeling Port LabelPoE and PoE+ Ports 10/100BASE-T PortsPort Description 100/1000 Mb/s SFP Module Slots 10/100 Mb/s SFP Module SlotsDual-Purpose Gigabit Ethernet Ports Supported SFPs Type of SFP Module ModelLEDs SYSPoE Router Compact Flash Memory Cards CF1 Label on Cisco IOS Router Description Interface NameCF0 Pre-Installation InstallationInstallation Warning Statements Installation Removing the Slot Divider From the CGR 2010 Router Installing the Switch Module in the CGR 2010 Router Connecting to the Network Connecting the Copper Switch ModuleConnecting the Fiber Switch Module Connecting the Copper Model to the NetworkRemoving the Switch Module Connecting the SFP Fiber Model to the NetworkOL-23421-02 Express Setup Express SetupSystem Requirements Recessed Express Setup Button Express Setup Window Field Description Vlan IDResetting the Switch Module Troubleshooting Express SetupProblem Resolution Follow the steps in Express Setup, Using the Device Manager Managing the Switch ModuleCisco Configuration Professional Accessing the Switch Module Other Management OptionsInterface IP Address Method Status ProtocolCommand Purpose Disconnecting from the Switch ModulePurpose Connecting Devices to the Switch Module SFP Module Slots 237941 Dual-Purpose Port with RJ-45 and SFP Connectors 237964 Dual-Purpose Connectors Verifying Port ConnectivityOL-23421-02 Connector Specifications Cable and ConnectorsSFP Module Connectors Dual-Purpose Ports Cables and AdaptersSFP Module Cables Core Modal Wavelength Extended temperature SFPsCommercial SFPs Bandwidth Type of SFP Module Nanometers Fiber Type Cable PinoutsMHz/km1 Cable Distance Figure A-6 OL-23421-02
Top Page Image Contents