Cisco Systems PAP2 manual Front Panel, Phone Adapter’s LEDs are located on the front panel

Page 10

Phone Adapter with 2 Ports for Voice-over-IP

The Front Panel

The Phone Adapter’s LEDs are located on the front panel.

	Figure 2-2: Front Panel
PHONE 1 LED	Blue. The PHONE 1 LED is solidly lit when a telephone or fax machine has a registered
	connection to Vonage through the PHONE 1 port. (The connection is registered if your
	Internet phone service account is active.) It flashes when the phone is being used or an
	incoming call has been detected.
PHONE 2 LED	Blue. The PHONE 2 LED is solidly lit when a telephone or fax machine has a registered
	connection to Vonage through the PHONE 2 port. It flashes when the phone is being used or
	an incoming call has been detected.
ETHERNET LED	Blue. The ETHERNET LED lights up when the Phone Adapter is connected to your network
	through the Ethernet port. It flashes when there is data being sent or received.
Power LED	Blue/Red. The Power LED lights up when the Phone Adapter is powered on and ready. It
	flashes when the Phone Adapter is booting up, undergoing a self-test, or performing a
	firmware upgrade. The LED lights up red when the Phone Adapter has failed its self-test or
	is malfunctioning. Refer to “Appendix A: Troubleshooting” for more information.
4	Chapter 2: Getting to Know the Phone Adapter
	The Front Panel

Image 10

Contents Phone Adapter Page How to Use this Guide Copyright and TrademarksPhone Adapter with 2 Ports for Voice-over-IP Table of Contents Back Panel Front PanelWelcome IntroductionWhat’s in this Guide? Introduction Getting to Know the Phone Adapter Back Panel PortsIncoming call has been detected Front PanelPhone Adapter’s LEDs are located on the front panel An incoming call has been detectedOverview Connecting the Phone AdapterInstructions for Connecting the Phone Adapter InternetFollow the instructions provided by Vonage Connect the Telephone CableRemove the plate from the Phone Adapter’s bottom panel Placement OptionsStand Option Phone Adapter’s Interactive Voice Response MenuWall-Mount Option Measurement between Wall-Mount SlotsAccessing the Interactive Voice Response Menu Using the Phone Adapter’s Interactive Voice Response MenuUsing the Interactive Voice Response Menu Not press any other keys until you Use this command to enter Response MenuInteractive Voice Response Menu Key or hang up to exitEnter 0 to disable Has been enabled or disabled. If101 Enter 1 to enable Check Dhcp 100Subnet Mask Mask using Address usingStatic IP address When entering a Decimal point Network mask When entering a Decimal pointPhone Adapter Manual Reboot 732668 Address Address usingStatic gateway IP address When entering a Decimal point 131 Enter the IPConfiguring the Settings for Your Internet Phone Service Appendix a Troubleshooting Common Problems and SolutionsAppendix a Troubleshooting IP address Phone Adapter Internet phone 53 to Application Start and End Protocol IP Address EnableInternet phone 5060 to IP address Phone Adapter Internet phone 69 toPhone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Frequently Asked Questions Ethernet LED does not light upCan I make calls while I’m browsing the Internet? Shared Resources Appendix B Windows HelpNetwork Neighborhood/My Network Places Appendix B Windows Help Appendix C Glossary Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications Storage Humidity ~90% Non-Condensing Dimensions 98 x 3.98 x H x DMm x 101 mm x 15 mm Appendix E Warranty Information Limited WarrantyAppendix E Warranty Information Appendix F Regulatory Information FCC StatementAppendix F Regulatory Information Linksys VonageToll-free from US