Cisco Systems
PAP2
manual
Appendix B Windows Help
Troubleshooting
Specifications
FAQ
Connecting the Phone Adapter
Warranty
Dimension
How to
Placement Options
Enter 1 to enable
Address using
Page 32
Phone Adapter with 2 Ports for
Voice-over-IP
26
Appendix B: Windows Help
Page 31
Page 33
Image 32
Page 31
Page 33
Contents
Phone Adapter
Page
How to Use this Guide
Copyright and Trademarks
Phone Adapter with 2 Ports for Voice-over-IP
Table of Contents
Back Panel
Front Panel
What’s in this Guide?
Introduction
Welcome
Introduction
Getting to Know the Phone Adapter
Back Panel Ports
Front Panel
Phone Adapter’s LEDs are located on the front panel
Incoming call has been detected
An incoming call has been detected
Connecting the Phone Adapter
Instructions for Connecting the Phone Adapter
Overview
Internet
Follow the instructions provided by Vonage
Connect the Telephone Cable
Placement Options
Stand Option
Remove the plate from the Phone Adapter’s bottom panel
Phone Adapter’s Interactive Voice Response Menu
Wall-Mount Option
Measurement between Wall-Mount Slots
Using the Interactive Voice Response Menu
Using the Phone Adapter’s Interactive Voice Response Menu
Accessing the Interactive Voice Response Menu
Use this command to enter Response Menu
Interactive Voice Response Menu
Not press any other keys until you
Key or hang up to exit
Has been enabled or disabled. If
101 Enter 1 to enable
Enter 0 to disable
Check Dhcp 100
Address using
Static IP address When entering a Decimal point
Subnet Mask Mask using
Network mask When entering a Decimal point
Address Address using
Static gateway IP address When entering a Decimal point
Phone Adapter Manual Reboot 732668
131 Enter the IP
Configuring the Settings for Your Internet Phone Service
Appendix a Troubleshooting
Common Problems and Solutions
Appendix a Troubleshooting
Application Start and End Protocol IP Address Enable
Internet phone 5060 to
IP address Phone Adapter Internet phone 53 to
IP address Phone Adapter Internet phone 69 to
Phone Adapter with 2 Ports for Voice-over-IP
Application Start and End Protocol IP Address Enable
Phone Adapter with 2 Ports for Voice-over-IP
Phone Adapter with 2 Ports for Voice-over-IP
Application Start and End Protocol IP Address Enable
Frequently Asked Questions
Ethernet LED does not light up
Can I make calls while I’m browsing the Internet?
Network Neighborhood/My Network Places
Appendix B Windows Help
Shared Resources
Appendix B Windows Help
Appendix C Glossary
Appendix C Glossary
Phone Adapter with 2 Ports for Voice-over-IP
Phone Adapter with 2 Ports for Voice-over-IP
Phone Adapter with 2 Ports for Voice-over-IP
Phone Adapter with 2 Ports for Voice-over-IP
Appendix D Specifications
Mm x 101 mm x 15 mm
Dimensions 98 x 3.98 x H x D
Storage Humidity ~90% Non-Condensing
Appendix E Warranty Information
Limited Warranty
Appendix E Warranty Information
Appendix F Regulatory Information
FCC Statement
Appendix F Regulatory Information
Toll-free from US
Vonage
Linksys
Related pages
Troubleshooting tips for Acer EFL50
Technical Specifications for Eiki LC-XB28
Error messages con’t from previous for Furuno SC-120
Lubrication Chart for Poulan 2005-04
For best results when steaming fish and seafood for Sunbeam RC5600
3ware Escalade ATA RAID Controller Installation Guide for IBM 8000 Series
PD45131 Parts List for Stanley Black & Decker PD45
Remote Control Operation / Code List for Panasonic TH 50VX100U
Dhcpd Server Setup for Intel I/O Processor
W1774 Parts List for Woodstock W1774
How do I wire the
field terminals
for the NT-8116-DO-AC model?
Top
Page
Image
Contents