Cisco Systems PAP2 manual Phone Adapter with 2 Ports for Voice-over-IP

Page 24

Phone Adapter with 2 Ports for Voice-over-IP

4.Wait two minutes, and then power on your cable or DSL modem by plugging its power adapter into an electrical outlet.

5.Wait two minutes, and then power on the router by plugging its power adapter into an electrical outlet.

6.Wait five minutes, and then power on the Phone Adapter by plugging its power adapter into an electrical outlet.

7.Reboot one of your networked computers, and check to see if you have an active Internet connection.

8.Pick up the telephone. You should now have a dial tone.

•Set up port forwarding on your router. You must specify that four port ranges be forwarded to the IP address of the Phone Adapter. These four port ranges are as follows: 5060-5061 (UDP), 53-53 (UDP), 69-69 (UDP), and 10000-20000 (UDP).

Before you set up port forwarding on your router, change two of the Phone Adapter’s settings using its Interactive Voice Response Menu. First, disable its DHCP feature, and then assign a static IP address to the Phone Adapter. Refer to “Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu” for instructions.

If you have a non-Linksys router, refer to its documentation for instructions. If you have a Linksys router, then follow these instructions:

1.On one of your networked computers, open your web browser.

2.Access the Router’s Web-based Utility by going to http://192.168.1.1 or the IP address of the Router.

3.A login screen will appear. Leave the User Name field blank. Enter the Router’s password (the default is admin) in the Password field. Then click the OK button.

4.Click the Applications & Gaming tab, and then click the Port Range Forwarding tab.

18	Appendix A: Troubleshooting
	Common Problems and Solutions

Image 24

Contents Phone Adapter Page How to Use this Guide Copyright and TrademarksPhone Adapter with 2 Ports for Voice-over-IP Table of Contents Back Panel Front PanelIntroduction WelcomeWhat’s in this Guide? Introduction Getting to Know the Phone Adapter Back Panel PortsFront Panel Phone Adapter’s LEDs are located on the front panelIncoming call has been detected An incoming call has been detectedConnecting the Phone Adapter Instructions for Connecting the Phone AdapterOverview InternetFollow the instructions provided by Vonage Connect the Telephone CablePlacement Options Stand OptionRemove the plate from the Phone Adapter’s bottom panel Phone Adapter’s Interactive Voice Response MenuWall-Mount Option Measurement between Wall-Mount SlotsUsing the Phone Adapter’s Interactive Voice Response Menu Accessing the Interactive Voice Response MenuUsing the Interactive Voice Response Menu Use this command to enter Response Menu Interactive Voice Response MenuNot press any other keys until you Key or hang up to exitHas been enabled or disabled. If 101 Enter 1 to enableEnter 0 to disable Check Dhcp 100Address using Static IP address When entering a Decimal pointSubnet Mask Mask using Network mask When entering a Decimal pointAddress Address using Static gateway IP address When entering a Decimal pointPhone Adapter Manual Reboot 732668 131 Enter the IPConfiguring the Settings for Your Internet Phone Service Appendix a Troubleshooting Common Problems and SolutionsAppendix a Troubleshooting Application Start and End Protocol IP Address Enable Internet phone 5060 toIP address Phone Adapter Internet phone 53 to IP address Phone Adapter Internet phone 69 toPhone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Frequently Asked Questions Ethernet LED does not light upCan I make calls while I’m browsing the Internet? Appendix B Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix B Windows Help Appendix C Glossary Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications Dimensions 98 x 3.98 x H x D Storage Humidity ~90% Non-CondensingMm x 101 mm x 15 mm Appendix E Warranty Information Limited WarrantyAppendix E Warranty Information Appendix F Regulatory Information FCC StatementAppendix F Regulatory Information Vonage LinksysToll-free from US