Cisco Systems PAP2 manual Phone Adapter with 2 Ports for Voice-over-IP

Page 27

6.Wait five minutes, and then power on the Phone Adapter by plugging its power adapter into an electrical outlet.

7.Reboot one of your networked computers, and check to see if you have an active Internet connection.

•Set up port forwarding on your router. You must specify that four port ranges be forwarded to the IP address of the Phone Adapter. These four port ranges are as follows: 5060-5061 (UDP), 53-53 (UDP), 69-69 (UDP), and 10000-20000 (UDP).

Before you set up port forwarding on your router, change two of the Phone Adapter’s settings using its Interactive Voice Response Menu. First, disable its DHCP feature, and then assign a static IP address to the Phone Adapter. Refer to “Chapter 4: Using the Phone Adapter’s Interactive Voice Response Menu” for instructions.

If you have a non-Linksys router, refer to its documentation for instructions. If you have a Linksys router, then follow these instructions:

1.On one of your networked computers, open your web browser.

2.Access the Router’s Web-based Utility by going to http://192.168.1.1 or the IP address of the Router.

3.A login screen will appear. Leave the User Name field blank. Enter the Router’s password (the default is admin) in the Password field. Then click the OK button.

4.Click the Applications & Gaming tab, and then click the Port Range Forwarding tab.

5.For each port range you must specify, enter a different name in the Application field. Then enter the number or range of external port(s) used by the Phone Adapter.

6.Select the protocol you will be using, UDP.

7.Enter the IP address of the Phone Adapter. For example, if the Phone Adapter’s IP address is 192.168.1.100, you would enter 100 in the field provided.

Appendix A: Troubleshooting

Phone Adapter with 2 Ports for Voice-over-IP

21

Common Problems and Solutions

Image 27

Contents Phone Adapter Page Copyright and Trademarks How to Use this GuidePhone Adapter with 2 Ports for Voice-over-IP Table of Contents Front Panel Back PanelIntroduction WelcomeWhat’s in this Guide? Introduction Back Panel Ports Getting to Know the Phone AdapterAn incoming call has been detected Front PanelPhone Adapter’s LEDs are located on the front panel Incoming call has been detectedInternet Connecting the Phone AdapterInstructions for Connecting the Phone Adapter OverviewConnect the Telephone Cable Follow the instructions provided by VonagePhone Adapter’s Interactive Voice Response Menu Placement OptionsStand Option Remove the plate from the Phone Adapter’s bottom panelMeasurement between Wall-Mount Slots Wall-Mount OptionUsing the Phone Adapter’s Interactive Voice Response Menu Accessing the Interactive Voice Response MenuUsing the Interactive Voice Response Menu Key or hang up to exit Use this command to enter Response MenuInteractive Voice Response Menu Not press any other keys until youCheck Dhcp 100 Has been enabled or disabled. If101 Enter 1 to enable Enter 0 to disableNetwork mask When entering a Decimal point Address usingStatic IP address When entering a Decimal point Subnet Mask Mask using131 Enter the IP Address Address usingStatic gateway IP address When entering a Decimal point Phone Adapter Manual Reboot 732668Configuring the Settings for Your Internet Phone Service Common Problems and Solutions Appendix a TroubleshootingAppendix a Troubleshooting IP address Phone Adapter Internet phone 69 to Application Start and End Protocol IP Address EnableInternet phone 5060 to IP address Phone Adapter Internet phone 53 toPhone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Ethernet LED does not light up Frequently Asked QuestionsCan I make calls while I’m browsing the Internet? Appendix B Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix B Windows Help Appendix C Glossary Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications Dimensions 98 x 3.98 x H x D Storage Humidity ~90% Non-CondensingMm x 101 mm x 15 mm Limited Warranty Appendix E Warranty InformationAppendix E Warranty Information FCC Statement Appendix F Regulatory InformationAppendix F Regulatory Information Vonage LinksysToll-free from US