Cisco Systems PAP2 Application Start and End Protocol IP Address Enable, Internet phone 5060 to

Page 23

Phone Adapter with 2 Ports for Voice-over-IP

8. Repeat steps 5-7 until you have entered all four port ranges for the Phone Adapter.

Application	Start and End	Protocol	IP Address	Enable

Internet phone 1	5060 to 5061	UDP	(IP address of	X
			Phone Adapter)

Internet phone 2	53 to 53	UDP	(IP address of	X
			Phone Adapter)

Internet phone 3	69 to 69	UDP	(IP address of	X
			Phone Adapter)

Internet phone 4	10000 to 20000	UDP	(IP address of	X
			Phone Adapter)

9.Check the Enable option for the port services you want to use.

10.When you have completed the configuration, click the Save Settings button.

2.When I make a telephone call, the call doesn’t go through; instead, I hear a fast busy signal. Go through this checklist until your problem is solved:

•Vonage supports 7-, 10-, and 11-digit dialing. Use 7-, 10-, or 11-digit dialing for calls within the same area code as your Vonage phone number. Use 10- or 11-digit dialing for calls outside of your area code.

•Follow these instructions to reboot your cable or DSL modem, Phone Adapter, and router:

1.Power off your cable or DSL modem by unplugging its power adapter.

2.Power off the router by unplugging its power adapter.

3.Power off the Phone Adapter by unplugging its power adapter.

Appendix A: Troubleshooting

17

Common Problems and Solutions

Image 23

Contents Phone Adapter Page Copyright and Trademarks How to Use this GuidePhone Adapter with 2 Ports for Voice-over-IP Table of Contents Front Panel Back PanelWhat’s in this Guide? IntroductionWelcome Introduction Back Panel Ports Getting to Know the Phone AdapterAn incoming call has been detected Front PanelPhone Adapter’s LEDs are located on the front panel Incoming call has been detectedInternet Connecting the Phone AdapterInstructions for Connecting the Phone Adapter OverviewConnect the Telephone Cable Follow the instructions provided by VonagePhone Adapter’s Interactive Voice Response Menu Placement OptionsStand Option Remove the plate from the Phone Adapter’s bottom panelMeasurement between Wall-Mount Slots Wall-Mount OptionUsing the Interactive Voice Response Menu Using the Phone Adapter’s Interactive Voice Response MenuAccessing the Interactive Voice Response Menu Key or hang up to exit Use this command to enter Response MenuInteractive Voice Response Menu Not press any other keys until youCheck Dhcp 100 Has been enabled or disabled. If101 Enter 1 to enable Enter 0 to disableNetwork mask When entering a Decimal point Address usingStatic IP address When entering a Decimal point Subnet Mask Mask using131 Enter the IP Address Address usingStatic gateway IP address When entering a Decimal point Phone Adapter Manual Reboot 732668Configuring the Settings for Your Internet Phone Service Common Problems and Solutions Appendix a TroubleshootingAppendix a Troubleshooting IP address Phone Adapter Internet phone 69 to Application Start and End Protocol IP Address EnableInternet phone 5060 to IP address Phone Adapter Internet phone 53 toPhone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Ethernet LED does not light up Frequently Asked QuestionsCan I make calls while I’m browsing the Internet? Network Neighborhood/My Network Places Appendix B Windows HelpShared Resources Appendix B Windows Help Appendix C Glossary Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications Mm x 101 mm x 15 mm Dimensions 98 x 3.98 x H x DStorage Humidity ~90% Non-Condensing Limited Warranty Appendix E Warranty InformationAppendix E Warranty Information FCC Statement Appendix F Regulatory InformationAppendix F Regulatory Information Toll-free from US VonageLinksys