Cisco Systems AS5400XM quick start Dfc

Page 12

Figure 15 Installing a Feature Card in a Cisco AS5400XM Universal Gateway

 

37165

Step 3

Align the captive screws with their holes, and seat the card completely.

Step 4

Tighten the screws to secure the feature card to the chassis. (See Figure 16 and Figure 17.)

Figure 16 Tighten the Captive Screws on the Cisco AS5350XM Universal Gateway

Chassis

0

1

Rx Tx

2 PRI

ACT OK

36817

Captive

DFC

Captive

screw

 

screw

 

Carrier

 

 

card

Figure 17 Tighten the Captive Screws on the Cisco AS5400XM Universal Gateway

Captive

screwCaptive screw

37170

Step 5 Check the card LEDs to verify that the card is working properly. The following table summarizes the LED functions for the feature cards.

12

Image 12
Contents Cisco AS5350XM and Cisco AS5400XM Universal Gateways Cisco 90-Day Limited Hardware Warranty Terms Duration of Hardware WarrantyReplacement, Repair, or Refund Policy for Hardware To Receive a Return Materials Authorization RMA NumberDocuments, Equipment, and Tools User DocumentationCisco IOS Software Documentation Command References New Feature DocumentationItems Not Included Release NotesInstall Chassis Safety InformationSetting Up the Chassis Rack-Mounting the ChassisRequired Tools and Equipment Attaching BracketsDesktop Installation Installation in a RackChassis Ground Connection Cisco AS5350XM Universal Gateway Ground Lug AttachmentInstall Modules Installing Carrier CardsInstalling a Carrier Card Blank Feature Card Cover Installing Feature Cards While the housing is open. StatementDFC Feature Card State DescriptionLED System Management and Power Connections Connect CablesColor or Port or Connection Type Cable WAN, LAN, and Voice Connections Connect a Console TerminalPort or Connection Color or Type Cable Console port RJ-45 Connect to an Ethernet Network Connect to a WAN T1/E1 8 PRI Connector RJ-45 jack E1 cable Cable RJ-45 jack T3 DFC Internet Statement Situation. StatementPin1 Description Connect AC Power Connect DC Power Position. StatementPower switch To DC source Last. StatementCisco AS5400XM Universal Gateway DC Power Supply Connections Power Up the Universal Gateway Checklist for Power UpPower-Up Procedure Perform Initial Configuration Initial Configuration Using the Setup Command FacilityEnter a hostname for the gateway Press Enter for every slot, port, and channel Initial Configuration Using the CLI Manual Configuration Router# configure terminalVerifying the Hostname and Passwords Configuring Local AAA Security Gateway# configure terminalGateway# show privilege Configuring Basic Dial Access Configuring the Asynchronous Group Interface Gatewayconfig# interface group-asyncGateway# ping Verifying the Group Interface Configuration Gateway# show interface async 4/0Gateway# show async status Configuring a T1 or E1 Feature Card Configuring a Channelized T3 Feature Card Verifying Channelized T1 or E1 Controller OperationGateway# show controller t1 1/7 Verifying Channelized T3 Controller Operation Gateway# show controller t3 1/0Configuring Isdn PRI Area Keyword Switch Type Gatewayconfig# controller t3 7/016Verifying Interface Configuration Gateway# show controller t1 1/0Gateway# show isdn service Gateway# show running-configGateway# show isdn status Configuring the D Channels for Isdn Signaling Gatewayconfig# interface serial 1/023 Gatewayconfig-if#ip address 172.16.254.254Gatewayconfig-if#isdn incoming-voice modem Configuring the Universal Port or Dial-Only Feature Cards Verifying D Channel ConfigurationGateway# show interface serial 1/023 Feature Description SPE FirmwareVerifying the SPE Configuration Configuring the Voice Feature Card Gateway# show lineUpgrade DSP Firmware on the Voice Feature Card Configure Clocking Feature Card PortsVerifying the Firmware Upgrade Gateway# show voice dsp versionClocking Configuration Examples Gatewayconfig# dial-tdm-clock priority 1 externalExternal Clock Free-Running ClockGatewayconfig# dial-tdm-clock priority 2 4/6 Gatewayconfig# dial-tdm-clock priority 2 1/019Gatewayconfig# dial-tdm-clock priority 3 free Verify ClockingCT3 Saving Configuration Changes Gateway# copy running-config startup-configVoice over IP PrerequisitesWhere to Go Next Configuration TasksFor new features associated with a software release Slot Numbering Obtaining DocumentationCisco.com Product Documentation DVDDocumentation Feedback Cisco Product Security OverviewOrdering Documentation Reporting Security Problems in Cisco Products Obtaining Technical AssistanceCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information Page Page USA
Related manuals
Manual 104 pages 52.67 Kb