Cisco Systems AS5400XM quick start Led

Page 14

Table 1

LEDs (continued)

 

 

 

 

 

 

Feature Card

LED

State

Description

 

 

 

 

 

CT3 feature

 

ACTIVITY (ACT)

Fast flicker

The feature card is up and running.

card

 

 

 

 

 

 

Slow flicker

The feature card is not yet fully functional.

 

 

 

 

 

 

 

 

 

 

OK/MAINT

On (green)

The feature card passed initial power-up diagnostics tests and

 

 

 

 

is operating normally.

 

 

 

 

 

 

 

 

Yellow

The feature card is busied out, but there are active calls.

 

 

 

 

Once all the calls are terminated the feature card will be

 

 

 

 

powered off.

 

 

 

 

The feature card is not functioning correctly.

 

 

 

 

 

 

 

 

Off

All calls associated with the feature card have been shut down,

 

 

 

 

and it is safe to remove the card with the system powered on.

 

 

 

 

 

 

 

M13 Alarm (MA)

On

One of the following is present on the T3 line:

 

 

 

 

Received alarm indication signal (RAIS)

 

 

 

 

Loss of signal (LOS)

 

 

 

 

Receive RED alarm (RRED)

 

 

 

 

Far-end receive failure (RFERF)1

 

 

 

Off

The operating condition is normal.

 

 

 

 

 

 

 

Remote Alarm (RA)

On

A T1 alarm condition has been encountered by software.

 

 

 

 

 

 

 

 

Off

The operating condition is normal.

 

 

 

 

 

 

 

Local Alarm (LA)

On

A T1 alarm condition has been encountered by software for a

 

 

 

 

particular port.

 

 

 

 

 

 

 

 

Off

The operating condition is normal.

 

 

 

 

 

 

 

T3 EN/DIS

Green

A CT3 feature card line connection exists, enabling normal

 

 

 

 

operation.

 

 

 

 

 

 

 

 

Yellow

Normal operation is disabled.

 

 

 

 

 

 

 

Low signal (LOS)

On

The T3 line interface unit (LIU) is experiencing a loss of signal.

 

 

 

 

 

 

 

 

Off

Remains off when operating condition is normal.

 

 

 

 

 

 

 

Network Loop

On

At least one T1 is unavailable.

 

 

(LOOP)

 

 

 

 

Off

The operating condition is normal.

 

 

 

 

 

 

 

 

Universal

 

ACTIVITY (ACT)

Flickering

There is call activity on the feature card.

port and

 

 

 

 

 

OK/MAINT

Green

The feature card passed initial power-up diagnostic tests and

dial-only

 

 

 

 

is operating normally.

feature card

 

 

 

 

 

 

 

 

 

Yellow

The feature card is busied out, but there are active calls.

 

 

 

 

 

 

 

Once all the calls are terminated the feature card will be

 

 

 

 

powered off.

 

 

 

 

The feature card is not functioning correctly.

 

 

 

 

 

 

 

 

Off

All calls associated with the feature card have been shut down,

 

 

 

 

and it is safe to remove the card with the system powered on.

 

 

 

 

 

14

Image 14
Contents Cisco AS5350XM and Cisco AS5400XM Universal Gateways Replacement, Repair, or Refund Policy for Hardware Cisco 90-Day Limited Hardware Warranty TermsDuration of Hardware Warranty To Receive a Return Materials Authorization RMA NumberCisco IOS Software Documentation Documents, Equipment, and ToolsUser Documentation Items Not Included Command ReferencesNew Feature Documentation Release NotesSetting Up the Chassis Install ChassisSafety Information Rack-Mounting the ChassisRequired Tools and Equipment Attaching BracketsDesktop Installation Installation in a RackChassis Ground Connection Cisco AS5350XM Universal Gateway Ground Lug AttachmentInstalling a Carrier Card Install ModulesInstalling Carrier Cards Blank Feature Card Cover Installing Feature Cards While the housing is open. StatementDFC Feature Card State DescriptionLED Color or Port or Connection Type Cable System Management and Power ConnectionsConnect Cables Port or Connection Color or Type Cable WAN, LAN, and Voice ConnectionsConnect a Console Terminal Console port RJ-45 Connect to an Ethernet Network Connect to a WAN T1/E1 8 PRI Connector RJ-45 jack E1 cable Cable RJ-45 jack T3 DFC Internet Statement Situation. StatementPin1 Description Connect AC Power Connect DC Power Position. StatementPower switch To DC source Last. StatementCisco AS5400XM Universal Gateway DC Power Supply Connections Power Up the Universal Gateway Checklist for Power UpPower-Up Procedure Perform Initial Configuration Initial Configuration Using the Setup Command FacilityEnter a hostname for the gateway Press Enter for every slot, port, and channel Initial Configuration Using the CLI Manual Configuration Router# configure terminalVerifying the Hostname and Passwords Gateway# show privilege Configuring Local AAA SecurityGateway# configure terminal Configuring Basic Dial Access Gateway# ping Configuring the Asynchronous Group InterfaceGatewayconfig# interface group-async Gateway# show async status Verifying the Group Interface ConfigurationGateway# show interface async 4/0 Configuring a T1 or E1 Feature Card Gateway# show controller t1 1/7 Configuring a Channelized T3 Feature CardVerifying Channelized T1 or E1 Controller Operation Verifying Channelized T3 Controller Operation Gateway# show controller t3 1/0Configuring Isdn PRI Area Keyword Switch Type Gatewayconfig# controller t3 7/016Verifying Interface Configuration Gateway# show controller t1 1/0Gateway# show isdn status Gateway# show isdn serviceGateway# show running-config Configuring the D Channels for Isdn Signaling Gatewayconfig-if#isdn incoming-voice modem Gatewayconfig# interface serial 1/023Gatewayconfig-if#ip address 172.16.254.254 Gateway# show interface serial 1/023 Configuring the Universal Port or Dial-Only Feature CardsVerifying D Channel Configuration Feature Description SPE FirmwareVerifying the SPE Configuration Configuring the Voice Feature Card Gateway# show lineUpgrade DSP Firmware on the Voice Feature Card Verifying the Firmware Upgrade Configure ClockingFeature Card Ports Gateway# show voice dsp versionExternal Clock Clocking Configuration ExamplesGatewayconfig# dial-tdm-clock priority 1 external Free-Running ClockGatewayconfig# dial-tdm-clock priority 3 free Gatewayconfig# dial-tdm-clock priority 2 4/6Gatewayconfig# dial-tdm-clock priority 2 1/019 Verify ClockingCT3 Voice over IP Saving Configuration ChangesGateway# copy running-config startup-config PrerequisitesFor new features associated with a software release Where to Go NextConfiguration Tasks Cisco.com Slot NumberingObtaining Documentation Product Documentation DVDOrdering Documentation Documentation FeedbackCisco Product Security Overview Cisco Technical Support & Documentation Website Reporting Security Problems in Cisco ProductsObtaining Technical Assistance Obtaining Additional Publications and Information Submitting a Service RequestDefinitions of Service Request Severity Page Page USA
Related manuals
Manual 104 pages 52.67 Kb