Cisco Systems AS5400XM quick start Desktop Installation, Installation in a Rack

Page 7

Installation in a Rack

Install the chassis in the rack. Rack-mounting screws are not provided. Use two screws for each side (supplied with the rack).

Figure 5 Installing the Cisco AS5350XM Universal Gateway in a Rack (19-Inch Rack)

35659

Figure 6 Installing the Cisco AS5400XM Universal Gateway in a Rack (19-Inch Rack)

29034

Desktop Installation

For desktop or shelf mounting, use the rubber “feet” shipped on a black adhesive strip with the chassis. They protect the chassis and provide a nonskid surface.

The location of the chassis is extremely important for proper operation. Equipment placed too close together, inadequate ventilation, and inaccessible panels can cause malfunctions and shutdowns, and can make maintenance difficult. The following information will help you to plan the location of the chassis:

Plan for access to both front and back panels of the chassis.

Ensure that the room where the chassis operates has adequate ventilation. Remember that electrical equipment generates heat. Ambient air temperature may not cool equipment to acceptable operating temperatures without adequate ventilation.

To attach the rubber feet, follow these steps:

Step 1 Locate the rubber feet that shipped with the chassis.

Step 2 Place the universal gateway upside-down on a smooth, flat surface.

Step 3 Peel the rubber feet off the black adhesive strip, and attach them adhesive-side-down at each corner of the underside of the chassis.

Step 4 Place the universal gateway top-side-up on a flat, smooth, secure surface.

7

Image 7
Contents Cisco AS5350XM and Cisco AS5400XM Universal Gateways To Receive a Return Materials Authorization RMA Number Cisco 90-Day Limited Hardware Warranty TermsDuration of Hardware Warranty Replacement, Repair, or Refund Policy for HardwareUser Documentation Documents, Equipment, and ToolsCisco IOS Software Documentation Release Notes Command ReferencesNew Feature Documentation Items Not IncludedRack-Mounting the Chassis Install ChassisSafety Information Setting Up the ChassisAttaching Brackets Required Tools and EquipmentInstallation in a Rack Desktop InstallationCisco AS5350XM Universal Gateway Ground Lug Attachment Chassis Ground ConnectionInstalling Carrier Cards Install ModulesInstalling a Carrier Card Blank Feature Card Cover While the housing is open. Statement Installing Feature CardsDFC State Description Feature CardLED Connect Cables System Management and Power ConnectionsColor or Port or Connection Type Cable Connect a Console Terminal WAN, LAN, and Voice ConnectionsPort or Connection Color or Type Cable Console port RJ-45 Connect to an Ethernet Network Connect to a WAN T1/E1 8 PRI Connector RJ-45 jack E1 cable Cable RJ-45 jack T3 DFC Internet Situation. Statement StatementPin1 Description Connect AC Power Position. Statement Connect DC PowerLast. Statement Power switch To DC sourceCisco AS5400XM Universal Gateway DC Power Supply Connections Checklist for Power Up Power Up the Universal GatewayPower-Up Procedure Initial Configuration Using the Setup Command Facility Perform Initial ConfigurationEnter a hostname for the gateway Press Enter for every slot, port, and channel Router# configure terminal Initial Configuration Using the CLI Manual ConfigurationVerifying the Hostname and Passwords Gateway# configure terminal Configuring Local AAA SecurityGateway# show privilege Configuring Basic Dial Access Gatewayconfig# interface group-async Configuring the Asynchronous Group InterfaceGateway# ping Gateway# show interface async 4/0 Verifying the Group Interface ConfigurationGateway# show async status Configuring a T1 or E1 Feature Card Verifying Channelized T1 or E1 Controller Operation Configuring a Channelized T3 Feature CardGateway# show controller t1 1/7 Gateway# show controller t3 1/0 Verifying Channelized T3 Controller OperationConfiguring Isdn PRI Gatewayconfig# controller t3 7/016 Area Keyword Switch TypeGateway# show controller t1 1/0 Verifying Interface ConfigurationGateway# show running-config Gateway# show isdn serviceGateway# show isdn status Configuring the D Channels for Isdn Signaling Gatewayconfig-if#ip address 172.16.254.254 Gatewayconfig# interface serial 1/023Gatewayconfig-if#isdn incoming-voice modem Verifying D Channel Configuration Configuring the Universal Port or Dial-Only Feature CardsGateway# show interface serial 1/023 SPE Firmware Feature DescriptionVerifying the SPE Configuration Gateway# show line Configuring the Voice Feature CardUpgrade DSP Firmware on the Voice Feature Card Gateway# show voice dsp version Configure ClockingFeature Card Ports Verifying the Firmware UpgradeFree-Running Clock Clocking Configuration ExamplesGatewayconfig# dial-tdm-clock priority 1 external External ClockVerify Clocking Gatewayconfig# dial-tdm-clock priority 2 4/6Gatewayconfig# dial-tdm-clock priority 2 1/019 Gatewayconfig# dial-tdm-clock priority 3 freeCT3 Prerequisites Saving Configuration ChangesGateway# copy running-config startup-config Voice over IPConfiguration Tasks Where to Go NextFor new features associated with a software release Product Documentation DVD Slot NumberingObtaining Documentation Cisco.comCisco Product Security Overview Documentation FeedbackOrdering Documentation Obtaining Technical Assistance Reporting Security Problems in Cisco ProductsCisco Technical Support & Documentation Website Definitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Page Page USA
Related manuals
Manual 104 pages 52.67 Kb