Cisco Systems AS5400XM quick start Situation. Statement

Page 25

Use a coaxial cable to connect a timing signal generator (TSG) to the building integrated timing supply (BITS) port. The BITS port is used for external clocking. (See Figure 32.)

Figure 32 Connecting the Cisco AS5350XM and Cisco AS5400XM Universal Gateways to a TSG

35841

To timing signal

generator

Coaxial cable BITS port

connector

Use a copper wire cable to connect to the alarm port.

Warning

The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device.

 

 

Statement 1019

 

 

 

 

 

 

Warning

Incorrect connection of this or connected equipment to a general purpose outlet could result in a hazardous

 

 

situation. Statement 87

 

 

 

To connect an alarm device to the alarm port, follow these steps.

Note The alarm connector is a 3-wire connector that plugs into a receptacle on the back of the chassis. The connector is provided in the accessory kit that ships with the universal gateway.

Step 1 Insert the 3-pin alarm port connector (included in the accessory kit) into the alarm port terminal block.

Step 2 Strip a minimum of 1/4 in. (0.625 cm) off the wire insulation to connect the stranded wires to the alarm connector. The maximum insulation strip length is 0.31 in. (0.78 cm).

Note Use stranded number 12 or number 14 AWG copper wires to connect an alarm device to the alarm port connector.

Step 3 Secure the wires to the alarm connector with the screws on the connector. (See Figure 33 and Figure 34.)

Caution The maximum tightening torque on the screws is 7 in.-lb (0.79 N-m).

25

Image 25
Contents Cisco AS5350XM and Cisco AS5400XM Universal Gateways Duration of Hardware Warranty Cisco 90-Day Limited Hardware Warranty TermsReplacement, Repair, or Refund Policy for Hardware To Receive a Return Materials Authorization RMA NumberUser Documentation Documents, Equipment, and ToolsCisco IOS Software Documentation New Feature Documentation Command ReferencesItems Not Included Release NotesSafety Information Install ChassisSetting Up the Chassis Rack-Mounting the ChassisAttaching Brackets Required Tools and EquipmentInstallation in a Rack Desktop InstallationCisco AS5350XM Universal Gateway Ground Lug Attachment Chassis Ground ConnectionInstalling Carrier Cards Install ModulesInstalling a Carrier Card Blank Feature Card Cover While the housing is open. Statement Installing Feature CardsDFC State Description Feature CardLED Connect Cables System Management and Power ConnectionsColor or Port or Connection Type Cable Connect a Console Terminal WAN, LAN, and Voice ConnectionsPort or Connection Color or Type Cable Console port RJ-45 Connect to an Ethernet Network Connect to a WAN T1/E1 8 PRI Connector RJ-45 jack E1 cable Cable RJ-45 jack T3 DFC Internet Situation. Statement StatementPin1 Description Connect AC Power Position. Statement Connect DC PowerLast. Statement Power switch To DC sourceCisco AS5400XM Universal Gateway DC Power Supply Connections Checklist for Power Up Power Up the Universal GatewayPower-Up Procedure Initial Configuration Using the Setup Command Facility Perform Initial ConfigurationEnter a hostname for the gateway Press Enter for every slot, port, and channel Router# configure terminal Initial Configuration Using the CLI Manual ConfigurationVerifying the Hostname and Passwords Gateway# configure terminal Configuring Local AAA SecurityGateway# show privilege Configuring Basic Dial Access Gatewayconfig# interface group-async Configuring the Asynchronous Group InterfaceGateway# ping Gateway# show interface async 4/0 Verifying the Group Interface ConfigurationGateway# show async status Configuring a T1 or E1 Feature Card Verifying Channelized T1 or E1 Controller Operation Configuring a Channelized T3 Feature CardGateway# show controller t1 1/7 Gateway# show controller t3 1/0 Verifying Channelized T3 Controller OperationConfiguring Isdn PRI Gatewayconfig# controller t3 7/016 Area Keyword Switch TypeGateway# show controller t1 1/0 Verifying Interface ConfigurationGateway# show running-config Gateway# show isdn serviceGateway# show isdn status Configuring the D Channels for Isdn Signaling Gatewayconfig-if#ip address 172.16.254.254 Gatewayconfig# interface serial 1/023Gatewayconfig-if#isdn incoming-voice modem Verifying D Channel Configuration Configuring the Universal Port or Dial-Only Feature CardsGateway# show interface serial 1/023 SPE Firmware Feature DescriptionVerifying the SPE Configuration Gateway# show line Configuring the Voice Feature CardUpgrade DSP Firmware on the Voice Feature Card Feature Card Ports Configure ClockingVerifying the Firmware Upgrade Gateway# show voice dsp versionGatewayconfig# dial-tdm-clock priority 1 external Clocking Configuration ExamplesExternal Clock Free-Running ClockGatewayconfig# dial-tdm-clock priority 2 1/019 Gatewayconfig# dial-tdm-clock priority 2 4/6Gatewayconfig# dial-tdm-clock priority 3 free Verify ClockingCT3 Gateway# copy running-config startup-config Saving Configuration ChangesVoice over IP PrerequisitesConfiguration Tasks Where to Go NextFor new features associated with a software release Obtaining Documentation Slot NumberingCisco.com Product Documentation DVDCisco Product Security Overview Documentation FeedbackOrdering Documentation Obtaining Technical Assistance Reporting Security Problems in Cisco ProductsCisco Technical Support & Documentation Website Definitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Page Page USA
Related manuals
Manual 104 pages 52.67 Kb