Cisco Systems AS5400XM quick start Verifying Channelized T3 Controller Operation

Page 44

Step 1 Use the enable command and password to enter privileged EXEC mode. You are in privileged EXEC mode when the prompt changes to Gateway#.

Gateway> enable

Password: password

Gateway#

Step 2 Enter global configuration mode. You are in global configuration mode when the prompt changes to Gateway(config)#.

Gateway# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Gateway(config)#

Step 3 Enter controller configuration mode to configure your T3 controller for slot 1 port 0. Slot values range from 1 to 7. The port number is always 0.

Gateway(config)# controller t3 1/0

Gateway(config-controller)#

Step 4 Enter the telco framing type, either c-bitor m23:

Gateway(config-controller)# framing c-bit

Step 5 Enter your clock source, either internal or line:

Gateway(config-controller)# clock source line

Step 6 Enter your cable length. Values range in feet from 0 to 450.

Gateway(config-controller)# cablelength 450

Step 7 Configure your T1 controllers. The range is 1 to 28.

To configure all 28 T1 controllers at once, enter:

Gateway(config-controller)# t1 1-28 controller

To omit specified T1 controllers while configuring others, specify them as needed. In this instance, T1 controllers 11–14, 21, 22, and 24–28 are not configured.

Gateway(config-controller)# t1 1-10,15-20,23 controller

Step 8 Return to privileged EXEC mode:

Gateway(config-controller)# Ctrl-Z

Gateway#

Tip To save the gateway configuration, save it to NVRAM. See the “Saving Configuration Changes” section on page 60.

Verifying Channelized T3 Controller Operation

To verify that your controller is up and running and that no alarms have been reported, enter the show controller command and specify the controller type, slot, and port numbers:

Gateway# show controller t3 1/0

T3 1/0 is up.

Applique type is Channelized T3

No alarms detected.

MDL transmission is disabled

FEAC code received:No code is being received

Framing is C-BIT Parity, Line Code is B3ZS, Clock Source is Internal Data in current interval (270 seconds elapsed):

0 Line Code Violations, 0 P-bit Coding Violation

44

Image 44
Contents Cisco AS5350XM and Cisco AS5400XM Universal Gateways Cisco 90-Day Limited Hardware Warranty Terms Duration of Hardware WarrantyReplacement, Repair, or Refund Policy for Hardware To Receive a Return Materials Authorization RMA NumberCisco IOS Software Documentation Documents, Equipment, and ToolsUser Documentation Command References New Feature DocumentationItems Not Included Release NotesInstall Chassis Safety InformationSetting Up the Chassis Rack-Mounting the ChassisRequired Tools and Equipment Attaching BracketsDesktop Installation Installation in a RackChassis Ground Connection Cisco AS5350XM Universal Gateway Ground Lug AttachmentInstalling a Carrier Card Install ModulesInstalling Carrier Cards Blank Feature Card Cover Installing Feature Cards While the housing is open. StatementDFC Feature Card State DescriptionLED Color or Port or Connection Type Cable System Management and Power ConnectionsConnect Cables Port or Connection Color or Type Cable WAN, LAN, and Voice ConnectionsConnect a Console Terminal Console port RJ-45 Connect to an Ethernet Network Connect to a WAN T1/E1 8 PRI Connector RJ-45 jack E1 cable Cable RJ-45 jack T3 DFC Internet Statement Situation. StatementPin1 Description Connect AC Power Connect DC Power Position. StatementPower switch To DC source Last. StatementCisco AS5400XM Universal Gateway DC Power Supply Connections Power Up the Universal Gateway Checklist for Power UpPower-Up Procedure Perform Initial Configuration Initial Configuration Using the Setup Command FacilityEnter a hostname for the gateway Press Enter for every slot, port, and channel Initial Configuration Using the CLI Manual Configuration Router# configure terminalVerifying the Hostname and Passwords Gateway# show privilege Configuring Local AAA SecurityGateway# configure terminal Configuring Basic Dial Access Gateway# ping Configuring the Asynchronous Group InterfaceGatewayconfig# interface group-async Gateway# show async status Verifying the Group Interface ConfigurationGateway# show interface async 4/0 Configuring a T1 or E1 Feature Card Gateway# show controller t1 1/7 Configuring a Channelized T3 Feature CardVerifying Channelized T1 or E1 Controller Operation Verifying Channelized T3 Controller Operation Gateway# show controller t3 1/0Configuring Isdn PRI Area Keyword Switch Type Gatewayconfig# controller t3 7/016Verifying Interface Configuration Gateway# show controller t1 1/0Gateway# show isdn status Gateway# show isdn serviceGateway# show running-config Configuring the D Channels for Isdn Signaling Gatewayconfig-if#isdn incoming-voice modem Gatewayconfig# interface serial 1/023Gatewayconfig-if#ip address 172.16.254.254 Gateway# show interface serial 1/023 Configuring the Universal Port or Dial-Only Feature CardsVerifying D Channel Configuration Feature Description SPE FirmwareVerifying the SPE Configuration Configuring the Voice Feature Card Gateway# show lineUpgrade DSP Firmware on the Voice Feature Card Configure Clocking Feature Card PortsVerifying the Firmware Upgrade Gateway# show voice dsp versionClocking Configuration Examples Gatewayconfig# dial-tdm-clock priority 1 externalExternal Clock Free-Running ClockGatewayconfig# dial-tdm-clock priority 2 4/6 Gatewayconfig# dial-tdm-clock priority 2 1/019Gatewayconfig# dial-tdm-clock priority 3 free Verify ClockingCT3 Saving Configuration Changes Gateway# copy running-config startup-configVoice over IP PrerequisitesFor new features associated with a software release Where to Go NextConfiguration Tasks Slot Numbering Obtaining DocumentationCisco.com Product Documentation DVDOrdering Documentation Documentation FeedbackCisco Product Security Overview Cisco Technical Support & Documentation Website Reporting Security Problems in Cisco ProductsObtaining Technical Assistance Obtaining Additional Publications and Information Submitting a Service RequestDefinitions of Service Request Severity Page Page USA
Related manuals
Manual 104 pages 52.67 Kb