Cisco Systems AS5400XM quick start Perform Initial Configuration

Page 33

Last reset from IOS reload Manufacture Cookie Info:

EEPROM Version 0x4, Board ID 0x4BD,

Board Hardware Version 1.11, Item Number 800-6572289-01, Board Revision 02, Serial Number JAB082904P4.

Processor 0x0, MAC Address badb.adba.d044 2 Gigabit Ethernet interfaces

6 Serial interfaces

648 terminal lines

1 Channelized T3 port

512K bytes of NVRAM.

125184K bytes of ATA External CompactFlash (Read/Write)

Press RETURN to get started!

Note If the rommon 1> prompt appears, your system has booted in ROM monitor mode. For information on the ROM monitor, see the universal gateway ROM monitor information in the Cisco IOS Configuration Fundamentals Configuration Guide for your Cisco IOS software release.

7Perform Initial Configuration

Note The information in this document applies to the Cisco AS5350XM and Cisco AS5400XM universal gateways.

At this point you can continue, using the setup command facility, or you can configure the universal gateway manually using the command-line interface (CLI).

The following section describes the procedure for the setup command facility for the initial configuration.

See the “Initial Configuration Using the CLI (Manual Configuration)” section on page 36 for information about manual configuration using the CLI.

Initial Configuration Using the Setup Command Facility

This section shows how to prepare the system to perform basic communication functions through its Ethernet and WAN interfaces.

Note The messages displayed depend on the Cisco IOS software release and cards installed in your system. The screen displays in this section are for reference only and might not exactly match the messages on your console.

Note If you make a mistake while using the setup command facility, you can exit and run the facility again. Press Ctrl-C, and type setup at the enable mode prompt (Router#).

Step 1 To proceed using the setup command facility, enter yes:

Would you like to enter the initial configuration dialog? [yes/no]: yes

At any point you may enter a question mark ‘?’ for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets ‘[]’.

33

Image 33
Contents Cisco AS5350XM and Cisco AS5400XM Universal Gateways Duration of Hardware Warranty Cisco 90-Day Limited Hardware Warranty TermsReplacement, Repair, or Refund Policy for Hardware To Receive a Return Materials Authorization RMA NumberDocuments, Equipment, and Tools User DocumentationCisco IOS Software Documentation New Feature Documentation Command ReferencesItems Not Included Release NotesSafety Information Install ChassisSetting Up the Chassis Rack-Mounting the ChassisAttaching Brackets Required Tools and EquipmentInstallation in a Rack Desktop InstallationCisco AS5350XM Universal Gateway Ground Lug Attachment Chassis Ground ConnectionInstall Modules Installing Carrier CardsInstalling a Carrier Card Blank Feature Card Cover While the housing is open. Statement Installing Feature CardsDFC State Description Feature CardLED System Management and Power Connections Connect CablesColor or Port or Connection Type Cable WAN, LAN, and Voice Connections Connect a Console TerminalPort or Connection Color or Type Cable Console port RJ-45 Connect to an Ethernet Network Connect to a WAN T1/E1 8 PRI Connector RJ-45 jack E1 cable Cable RJ-45 jack T3 DFC Internet Situation. Statement StatementPin1 Description Connect AC Power Position. Statement Connect DC PowerLast. Statement Power switch To DC sourceCisco AS5400XM Universal Gateway DC Power Supply Connections Checklist for Power Up Power Up the Universal GatewayPower-Up Procedure Initial Configuration Using the Setup Command Facility Perform Initial ConfigurationEnter a hostname for the gateway Press Enter for every slot, port, and channel Router# configure terminal Initial Configuration Using the CLI Manual ConfigurationVerifying the Hostname and Passwords Configuring Local AAA Security Gateway# configure terminalGateway# show privilege Configuring Basic Dial Access Configuring the Asynchronous Group Interface Gatewayconfig# interface group-asyncGateway# ping Verifying the Group Interface Configuration Gateway# show interface async 4/0Gateway# show async status Configuring a T1 or E1 Feature Card Configuring a Channelized T3 Feature Card Verifying Channelized T1 or E1 Controller OperationGateway# show controller t1 1/7 Gateway# show controller t3 1/0 Verifying Channelized T3 Controller OperationConfiguring Isdn PRI Gatewayconfig# controller t3 7/016 Area Keyword Switch TypeGateway# show controller t1 1/0 Verifying Interface ConfigurationGateway# show isdn service Gateway# show running-configGateway# show isdn status Configuring the D Channels for Isdn Signaling Gatewayconfig# interface serial 1/023 Gatewayconfig-if#ip address 172.16.254.254Gatewayconfig-if#isdn incoming-voice modem Configuring the Universal Port or Dial-Only Feature Cards Verifying D Channel ConfigurationGateway# show interface serial 1/023 SPE Firmware Feature DescriptionVerifying the SPE Configuration Gateway# show line Configuring the Voice Feature CardUpgrade DSP Firmware on the Voice Feature Card Feature Card Ports Configure ClockingVerifying the Firmware Upgrade Gateway# show voice dsp versionGatewayconfig# dial-tdm-clock priority 1 external Clocking Configuration ExamplesExternal Clock Free-Running ClockGatewayconfig# dial-tdm-clock priority 2 1/019 Gatewayconfig# dial-tdm-clock priority 2 4/6Gatewayconfig# dial-tdm-clock priority 3 free Verify ClockingCT3 Gateway# copy running-config startup-config Saving Configuration ChangesVoice over IP PrerequisitesWhere to Go Next Configuration TasksFor new features associated with a software release Obtaining Documentation Slot NumberingCisco.com Product Documentation DVDDocumentation Feedback Cisco Product Security OverviewOrdering Documentation Reporting Security Problems in Cisco Products Obtaining Technical AssistanceCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information Page Page USA
Related manuals
Manual 104 pages 52.67 Kb