Cisco Systems AS5400XM quick start Chassis Ground Connection

Page 8

Caution Do not place anything on top of the universal gateway that weighs more than 10 lb (4.5 kg). Excessive weight on top could damage the chassis.

Chassis Ground Connection

You must connect the chassis to a reliable earth ground by using the ground lug (provided) and size AWG 6 (13 mm2) wire.

To attach the chassis ground, follow these steps:

Step 1 Strip one end of the ground wire to expose approximately 0.75 in. (20 mm) of conductor.

Step 2 Crimp the ground wire to the ground lug, using a crimp tool of the appropriate size.

Step 3 Attach the ground lug to the chassis as shown in Figure 7 and Figure 8. Use a medium flat-blade screwdriver and the screws supplied with the ground lug. Tighten the screws to a torque of 8 to 10 in-lb (0.9 to 1.1 N-m).

Figure 7 Cisco AS5350XM Universal Gateway Ground Lug Attachment

Ground lug attachment

82735

Figure 8 Cisco AS5400XM Universal Gateway Ground Lug Attachment

82734

Ground lug attachment

Step 4 Connect the other end of the ground wire to a suitable grounding point at your site.

8

Image 8
Contents Cisco AS5350XM and Cisco AS5400XM Universal Gateways Cisco 90-Day Limited Hardware Warranty Terms Duration of Hardware WarrantyReplacement, Repair, or Refund Policy for Hardware To Receive a Return Materials Authorization RMA NumberCisco IOS Software Documentation Documents, Equipment, and ToolsUser Documentation Command References New Feature DocumentationItems Not Included Release NotesInstall Chassis Safety InformationSetting Up the Chassis Rack-Mounting the ChassisRequired Tools and Equipment Attaching BracketsDesktop Installation Installation in a RackChassis Ground Connection Cisco AS5350XM Universal Gateway Ground Lug AttachmentInstalling a Carrier Card Install ModulesInstalling Carrier Cards Blank Feature Card Cover Installing Feature Cards While the housing is open. StatementDFC Feature Card State DescriptionLED Color or Port or Connection Type Cable System Management and Power ConnectionsConnect Cables Port or Connection Color or Type Cable WAN, LAN, and Voice ConnectionsConnect a Console Terminal Console port RJ-45 Connect to an Ethernet Network Connect to a WAN T1/E1 8 PRI Connector RJ-45 jack E1 cable Cable RJ-45 jack T3 DFC Internet Statement Situation. StatementPin1 Description Connect AC Power Connect DC Power Position. StatementPower switch To DC source Last. StatementCisco AS5400XM Universal Gateway DC Power Supply Connections Power Up the Universal Gateway Checklist for Power UpPower-Up Procedure Perform Initial Configuration Initial Configuration Using the Setup Command FacilityEnter a hostname for the gateway Press Enter for every slot, port, and channel Initial Configuration Using the CLI Manual Configuration Router# configure terminalVerifying the Hostname and Passwords Gateway# show privilege Configuring Local AAA SecurityGateway# configure terminal Configuring Basic Dial Access Gateway# ping Configuring the Asynchronous Group InterfaceGatewayconfig# interface group-async Gateway# show async status Verifying the Group Interface ConfigurationGateway# show interface async 4/0 Configuring a T1 or E1 Feature Card Gateway# show controller t1 1/7 Configuring a Channelized T3 Feature CardVerifying Channelized T1 or E1 Controller Operation Verifying Channelized T3 Controller Operation Gateway# show controller t3 1/0Configuring Isdn PRI Area Keyword Switch Type Gatewayconfig# controller t3 7/016Verifying Interface Configuration Gateway# show controller t1 1/0Gateway# show isdn status Gateway# show isdn serviceGateway# show running-config Configuring the D Channels for Isdn Signaling Gatewayconfig-if#isdn incoming-voice modem Gatewayconfig# interface serial 1/023Gatewayconfig-if#ip address 172.16.254.254 Gateway# show interface serial 1/023 Configuring the Universal Port or Dial-Only Feature CardsVerifying D Channel Configuration Feature Description SPE FirmwareVerifying the SPE Configuration Configuring the Voice Feature Card Gateway# show lineUpgrade DSP Firmware on the Voice Feature Card Configure Clocking Feature Card PortsVerifying the Firmware Upgrade Gateway# show voice dsp versionClocking Configuration Examples Gatewayconfig# dial-tdm-clock priority 1 externalExternal Clock Free-Running ClockGatewayconfig# dial-tdm-clock priority 2 4/6 Gatewayconfig# dial-tdm-clock priority 2 1/019Gatewayconfig# dial-tdm-clock priority 3 free Verify ClockingCT3 Saving Configuration Changes Gateway# copy running-config startup-configVoice over IP PrerequisitesFor new features associated with a software release Where to Go NextConfiguration Tasks Slot Numbering Obtaining DocumentationCisco.com Product Documentation DVDOrdering Documentation Documentation FeedbackCisco Product Security Overview Cisco Technical Support & Documentation Website Reporting Security Problems in Cisco ProductsObtaining Technical Assistance Obtaining Additional Publications and Information Submitting a Service RequestDefinitions of Service Request Severity Page Page USA
Related manuals
Manual 104 pages 52.67 Kb