Cisco Systems Cisco ONS 15454 SDH manual Slot-0 Status=IpAddress

Page 13

Chapter 4 Turn Up Node

DLP-D64 Set the IP Address, Default Router, and Network Mask Using the LCD

Step 7 Return to your originating procedure (NTP).

DLP-D64 Set the IP Address, Default Router, and Network Mask Using the LCD

Purpose

This task changes the ONS 15454 SDH IP address, default router, and

 

network mask using the front panel LCD. Use this task if you cannot log

 

into CTC.

Tools/Equipment

None

Prerequisite Procedures

DLP-D332 Install the TCC2 Cards, page 2-7

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None

Note You cannot perform this task if the LCD IP Display on the node view Provisioning > Network tab is set to Display Only or Suppress Display. See “DLP-D249 Provision IP Settings” task on page 4-10to view or change the LCD IP Display field.

Note The LCD reverts to normal display mode after 5 seconds of button inactivity.

Step 1 On the ONS 15454 SDH front panel, repeatedly press the Slot button until Node appears on the LCD.

Step 2 Repeatedly press the Port button until the following displays:

•To change the node IP address, Status=IpAddress (Figure 4-1)

•To change the node network mask, Status=Net Mask

•To change the default router IP address, Status=Default Rtr

Figure 4-1 Selecting the IP Address Option

Slot Status Port

Slot-0

Status=IpAddress

FAN FAIL CRIT

MAJ

MIN

 

 

 

44089

Step 3 Press the Status button to display the node IP address (Figure 4-2), the node subnet mask length, or the default router IP address.

 

 

Cisco ONS 15454 SDH Procedure Guide, R4.6

 

 

 

 

 

 

January 2004

 

 

4-13

 

 

 

 

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Before You Begin Turn Up NodeInstall Cards and Fiber-Optic Cable NTP-D24 Verify Card InstallationStop. You have completed this procedure DLP-D74 Create a New User-Single Node NTP-D30 Create Users and Assign SecurityDLP-D75 Create a New User-Multiple Nodes Required/As Needed PurposeClick the Provisioning General tabs Confirmation dialog box, click Yes Node view, click the Provisioning General Power Monitor tabs NTP-D279 Set Power Monitor ThresholdsNTP-D169 Set Up CTC Network Access Click the Provisioning Network tabs DLP-D249 Provision IP SettingsCisco ONS 15454 SDH Procedure Guide, R4.6 Reboot Activity Active TCC2 LEDs Standby TCC2 LEDs Slot-0 Status=IpAddress Next Done Mod Cisco ONS 15454 SDH Reference Manual DLP-D65 Create a Static RouteClick the No Authentication button DLP-D250 Set Up or Change Open Shortest Path First ProtocolType- Choose Simple Password January DLP-D251 Set Up or Change Routing Information Protocol NTP-D27 Set Up the ONS 15454 SDH for Firewall Access Iiop port Port Function DLP-D68 Provision the Iiop Listener Port on the CTC Computer NTP-D28 Set Up TimingStop . You have completed this procedure DLP-D69 Set Up External or Line TimingUnframed , FAS , FAS + CAS DLP-D70 Set Up Internal Timing NTP-D170 Create Protection Groups Type Cards Description and Installation Requirements DLP-D71 Create a 11 Protection Group Click the Provisioning Protection tabs DLP-D72 Create a 1N Protection GroupDLP-D73 Create a 1+1 Protection Group Creating a Y-Cable Protection Group DLP-D252 Create a Y-Cable Protection GroupBox Figure NTP-D34 Set Up SnmpCreating an Snmp Trap Without Proxy January
Top Page Image Contents