Cisco Systems Cisco ONS 15454 SDH manual NTP-D279 Set Power Monitor Thresholds

Page 8

Chapter 4 Turn Up Node

NTP-D279 Set Power Monitor Thresholds

Step 6 Review the node information. If you need to make corrections, repeat Steps 3 through 5 to enter the corrections. If the information is correct, continue with the “NTP-D279 Set Power Monitor Thresholds” procedure on page 4-8.

Stop. You have completed this procedure.

NTP-D279 Set Power Monitor Thresholds

Purpose

This procedure provisions extreme high, high, extreme low, and low input

 

battery power thresholds within a –48 volts direct current (VDC)

 

environment. When the thresholds are crossed, the TCC2 generates

 

warning alarms in CTC.

Tools/Equipment

None

Prerequisite Procedures

NTP-D24 Verify Card Installation, page 4-2

Required/As Needed

Required

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Step 1

Complete the “DLP-D60 Log into CTC” task on page 3-24for the node you will set up. If you are

 

already logged in, continue with Step 2.

Step 2

In node view, click the Provisioning > General > Power Monitor tabs.

Step 3 To change the extreme low battery voltage threshold in 0.5 VDC increments, choose a voltage from the ELWBATVGVdc drop-down menu.

Step 4 To change the low battery voltage threshold in 0.5 VDC increments, choose a voltage from the LWBATVGVdc drop-down menu.

Step 5 To change the high battery voltage threshold in 0.5 VDC increments, choose a voltage from the HIBATVGVdc drop-down menu.

Step 6 To change the extreme high battery voltage threshold in 0.5 VDC increments, choose a voltage from the EHIBATVGVdc drop-down menu.

Step 7 Click Apply.

Stop. You have completed this procedure.

Cisco ONS 15454 SDH Procedure Guide, R4.6

4-8

January 2004

 

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Turn Up Node Before You BeginNTP-D24 Verify Card Installation Install Cards and Fiber-Optic CableStop. You have completed this procedure NTP-D30 Create Users and Assign Security DLP-D74 Create a New User-Single Node DLP-D75 Create a New User-Multiple Nodes Click the Provisioning General tabs PurposeRequired/As Needed Confirmation dialog box, click Yes NTP-D279 Set Power Monitor Thresholds Node view, click the Provisioning General Power Monitor tabsNTP-D169 Set Up CTC Network Access DLP-D249 Provision IP Settings Click the Provisioning Network tabsCisco ONS 15454 SDH Procedure Guide, R4.6 Reboot Activity Active TCC2 LEDs Standby TCC2 LEDs Slot-0 Status=IpAddress Next Done Mod DLP-D65 Create a Static Route Cisco ONS 15454 SDH Reference ManualType- Choose Simple Password DLP-D250 Set Up or Change Open Shortest Path First ProtocolClick the No Authentication button January DLP-D251 Set Up or Change Routing Information Protocol NTP-D27 Set Up the ONS 15454 SDH for Firewall Access Iiop port Port Function NTP-D28 Set Up Timing DLP-D68 Provision the Iiop Listener Port on the CTC ComputerDLP-D69 Set Up External or Line Timing Stop . You have completed this procedureUnframed , FAS , FAS + CAS DLP-D70 Set Up Internal Timing NTP-D170 Create Protection Groups Type Cards Description and Installation Requirements DLP-D71 Create a 11 Protection Group DLP-D72 Create a 1N Protection Group Click the Provisioning Protection tabsDLP-D73 Create a 1+1 Protection Group DLP-D252 Create a Y-Cable Protection Group Creating a Y-Cable Protection GroupNTP-D34 Set Up Snmp Box FigureCreating an Snmp Trap Without Proxy January
Top Page Image Contents