Cisco Systems Cisco ONS 15454 SDH manual DLP-D75 Create a New User-Multiple Nodes

Page 5

Chapter 4 Turn Up Node

DLP-D75 Create a New User—Multiple Nodes

•Password—Type the user password. The password must be a minimum of six and a maximum of

20 alphanumeric (a-z, A-Z, 0-9) and special (+, #, %) characters, where at least two characters are nonalphabetic and at least one character is a special character. The password must not contain the user name.

•Confirm Password—Type the password again to confirm it.

•Security Level—Choose a security level for the user: RETRIEVE, MAINTENANCE, PROVISIONING, or SUPERUSER. Refer to the Cisco ONS 15454 SDH Reference Manual for information about the capabilities provided with each level.

Note Each security level has a different idle time. The idle time is the length of time that CTC can remain idle before the password must be reentered. The defaults are: Retrieve user = unlimited, Maintenance user = 60 minutes, Provisioning user = 30 minutes, and Superuser = 15 minutes. To change the idle times, refer to the “NTP-D205 Modify Users and Change Security” procedure on page 12-25.

Step 4 Click OK.

Step 5 Return to your originating procedure (NTP).

DLP-D75 Create a New User—Multiple Nodes

Purpose

This task adds a new user to multiple ONS 15454 SDH nodes.

Tools/Equipment

None

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-24

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Superuser

Note All nodes where you want to add users must be accessible in network view.

Step 1 From the view menu, choose Go to Network View.

Step 2 Click the Provisioning > Security > Users tabs.

Step 3 In the Security window, click Create.

Step 4 In the Create User dialog box, enter the following:

•Name—Type the user name. The name must be a minimum of six and a maximum of 20 alphanumeric (a-z, A-Z, 0-9) characters.

•Password—Type the user password. The password must be a minimum of six and a maximum of

20 alphanumeric (a-z, A-Z, 0-9) and special (+, #, %) characters, where at least two characters are nonalphabetic and at least one character is a special character.

•Confirm Password—Type the password again to confirm it.

Cisco ONS 15454 SDH Procedure Guide, R4.6

 

January 2004

4-5

 

 

 

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Before You Begin Turn Up Node Install Cards and Fiber-Optic Cable NTP-D24 Verify Card InstallationStop. You have completed this procedure DLP-D74 Create a New User-Single Node NTP-D30 Create Users and Assign SecurityDLP-D75 Create a New User-Multiple Nodes Click the Provisioning General tabs PurposeRequired/As Needed Confirmation dialog box, click Yes Node view, click the Provisioning General Power Monitor tabs NTP-D279 Set Power Monitor ThresholdsNTP-D169 Set Up CTC Network Access Click the Provisioning Network tabs DLP-D249 Provision IP SettingsCisco ONS 15454 SDH Procedure Guide, R4.6 Reboot Activity Active TCC2 LEDs Standby TCC2 LEDs Slot-0 Status=IpAddress Next Done Mod Cisco ONS 15454 SDH Reference Manual DLP-D65 Create a Static RouteType- Choose Simple Password DLP-D250 Set Up or Change Open Shortest Path First ProtocolClick the No Authentication button January DLP-D251 Set Up or Change Routing Information Protocol NTP-D27 Set Up the ONS 15454 SDH for Firewall Access Iiop port Port Function DLP-D68 Provision the Iiop Listener Port on the CTC Computer NTP-D28 Set Up TimingStop . You have completed this procedure DLP-D69 Set Up External or Line TimingUnframed , FAS , FAS + CAS DLP-D70 Set Up Internal Timing NTP-D170 Create Protection Groups Type Cards Description and Installation Requirements DLP-D71 Create a 11 Protection Group Click the Provisioning Protection tabs DLP-D72 Create a 1N Protection GroupDLP-D73 Create a 1+1 Protection Group Creating a Y-Cable Protection Group DLP-D252 Create a Y-Cable Protection GroupBox Figure NTP-D34 Set Up SnmpCreating an Snmp Trap Without Proxy January
Top Page Image Contents