Cisco Systems Cisco ONS 15454 SDH manual DLP-D252 Create a Y-Cable Protection Group

Page 31

Chapter 4 Turn Up Node

DLP-D252 Create a Y-Cable Protection Group

DLP-D252 Create a Y-Cable Protection Group

Purpose

This task creates a Y-Cable protection group for any transponder

 

(TXP_MR_10G) or muxponder (MXP_2.5G_10G) card/port.

Tools/Equipment

Installed transponder or muxponder cards or preprovisioned slots.

Prerequisite Procedures

DLP-D60 Log into CTC, page 3-24

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Step 1 Verify that the transponder or muxponder cards are installed according to the Y-cable requirements specified in Table 4-3 on page 4-27.

Step 2 In node view, click the Provisioning > Protection tabs.

Step 3 In the Protection Groups list, click Create.

Step 4 In the Create Protection Group dialog box, enter the following:

•Name—Type a name for the protection group. The name can have up to 32 alphanumeric (a-z, A-Z,

0-9) characters. Special characters are permitted. For TL1 compatibility, do not use question marks (?), backslash (\), or double quote (“) characters.

•Type—Choose Y Cable from the drop-down menu.

•Protect Port—Choose the protect port from the drop-down menu. The menu displays the available transponder or muxponder ports. If transponder or muxponder cards are not installed, no ports appear in the drop-down menu.

•After you choose the protect port, a list of ports available for protection appear under Available Ports, as shown in Figure 4-7. If no cards are available, no ports appear. If no ports are available, you cannot complete this task until you install the physical cards or preprovision the

ONS 15454 SDH slots using the “DLP-D442 Preprovision a Slot” task on page 5-5 .

Figure 4-7 Creating a Y-Cable Protection Group

 

 

Cisco ONS 15454 SDH Procedure Guide, R4.6

 

 

 

 

 

 

January 2004

 

 

4-31

 

 

 

 

 

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Before You Begin Turn Up NodeInstall Cards and Fiber-Optic Cable NTP-D24 Verify Card InstallationStop. You have completed this procedure DLP-D74 Create a New User-Single Node NTP-D30 Create Users and Assign SecurityDLP-D75 Create a New User-Multiple Nodes Required/As Needed PurposeClick the Provisioning General tabs Confirmation dialog box, click Yes Node view, click the Provisioning General Power Monitor tabs NTP-D279 Set Power Monitor ThresholdsNTP-D169 Set Up CTC Network Access Click the Provisioning Network tabs DLP-D249 Provision IP SettingsCisco ONS 15454 SDH Procedure Guide, R4.6 Reboot Activity Active TCC2 LEDs Standby TCC2 LEDs Slot-0 Status=IpAddress Next Done Mod Cisco ONS 15454 SDH Reference Manual DLP-D65 Create a Static RouteClick the No Authentication button DLP-D250 Set Up or Change Open Shortest Path First ProtocolType- Choose Simple Password January DLP-D251 Set Up or Change Routing Information Protocol NTP-D27 Set Up the ONS 15454 SDH for Firewall Access Iiop port Port Function DLP-D68 Provision the Iiop Listener Port on the CTC Computer NTP-D28 Set Up TimingStop . You have completed this procedure DLP-D69 Set Up External or Line TimingUnframed , FAS , FAS + CAS DLP-D70 Set Up Internal Timing NTP-D170 Create Protection Groups Type Cards Description and Installation Requirements DLP-D71 Create a 11 Protection Group Click the Provisioning Protection tabs DLP-D72 Create a 1N Protection GroupDLP-D73 Create a 1+1 Protection Group Creating a Y-Cable Protection Group DLP-D252 Create a Y-Cable Protection GroupBox Figure NTP-D34 Set Up SnmpCreating an Snmp Trap Without Proxy January
Top Page Image Contents