Cisco Systems Cisco ONS 15454 SDH manual Next Done Mod

Page 14

Chapter 4 Turn Up Node

DLP-D64 Set the IP Address, Default Router, and Network Mask Using the LCD

Figure 4-2 Changing the IP Address

Slot Status Port

FAN FAIL CRIT

MAJ

MIN

172.020.214.107 <Next Done Mod>

44090

Step 4 Push the Slot button to move to the IP address or subnet mask digit you need to change. The selected digit flashes.

Tip The Slot, Status, and Port button positions correspond to the command position on the LCD. For example, in Figure 4-2, you press the Slot button to invoke the Next command and the Port button to invoke the Done command.

Step 5 Press the Port button to cycle the IP address or subnet mask to the correct digit.

Step 6 When the change is complete, press the Status button to return to the Node menu.

Step 7 Repeatedly press the Port button until the Save Configuration option appears (Figure 4-3).

Figure 4-3 Selecting the Save Configuration Option

Slot Status Port

Slot-0

Status=Save Cfg.

FAN FAIL CRIT

MAJ

MIN

 

 

 

Step 8 Press the Status button to choose the Save Configuration option.

A Save and REBOOT message appears (Figure 4-4).

Figure 4-4 Saving and Rebooting the TCC2

44091

Slot Status Port

Save and REBOOT?

<Apply Revert>

FAN FAIL CRIT

MAJ

MIN

 

 

 

44092

Step 9 Press the Slot button to apply the new IP address configuration, or press Port to cancel the configuration.

Saving the new configuration causes the TCC2 cards to reboot. During the reboot, a “Saving Changes - TCC Reset” message displays on the LCD. The LCD returns to the normal alternating display after the TCC2 reboot is complete (see Table 4-1 on page 4-12for reboot behavior).

Note The IP address and default router must be configured to be on the same subnet. If not, you cannot apply the configuration.

 

Cisco ONS 15454 SDH Procedure Guide, R4.6

4-14

January 2004

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Turn Up Node Before You BeginNTP-D24 Verify Card Installation Install Cards and Fiber-Optic CableStop. You have completed this procedure NTP-D30 Create Users and Assign Security DLP-D74 Create a New User-Single NodeDLP-D75 Create a New User-Multiple Nodes Click the Provisioning General tabs PurposeRequired/As Needed Confirmation dialog box, click Yes NTP-D279 Set Power Monitor Thresholds Node view, click the Provisioning General Power Monitor tabsNTP-D169 Set Up CTC Network Access DLP-D249 Provision IP Settings Click the Provisioning Network tabs Cisco ONS 15454 SDH Procedure Guide, R4.6 Reboot Activity Active TCC2 LEDs Standby TCC2 LEDs Slot-0 Status=IpAddress Next Done Mod DLP-D65 Create a Static Route Cisco ONS 15454 SDH Reference ManualType- Choose Simple Password DLP-D250 Set Up or Change Open Shortest Path First ProtocolClick the No Authentication button January DLP-D251 Set Up or Change Routing Information Protocol NTP-D27 Set Up the ONS 15454 SDH for Firewall Access Iiop port Port Function NTP-D28 Set Up Timing DLP-D68 Provision the Iiop Listener Port on the CTC ComputerDLP-D69 Set Up External or Line Timing Stop . You have completed this procedureUnframed , FAS , FAS + CAS DLP-D70 Set Up Internal Timing NTP-D170 Create Protection Groups Type Cards Description and Installation Requirements DLP-D71 Create a 11 Protection Group DLP-D72 Create a 1N Protection Group Click the Provisioning Protection tabsDLP-D73 Create a 1+1 Protection Group DLP-D252 Create a Y-Cable Protection Group Creating a Y-Cable Protection GroupNTP-D34 Set Up Snmp Box FigureCreating an Snmp Trap Without Proxy January
Top Page Image Contents