Cisco Systems Cisco ONS 15454 SDH manual NTP-D27 Set Up the ONS 15454 SDH for Firewall Access

Page 19

Chapter 4 Turn Up Node

NTP-D27 Set Up the ONS 15454 SDH for Firewall Access

Step 6 If you want to complete an address summary, complete the following steps. If not, continue with Step 7. Complete the address summary only if the ONS 15454 SDH is a gateway NE with multiple external ONS 15454 SDH NEs attached with IP addresses in different subnets.

a.In the RIP Address Summary area, click Create.

b.In the Create Address Summary dialog box, complete the following:

•Summary Address—Enter the summary IP address.

•Mask Length—Enter the subnet mask length using the up and down arrows.

•Hops—Enter the number of hops. The smaller the number of hops, the higher the priority.

c.Click OK.

Step 7 Return to your originating procedure (NTP).

NTP-D27 Set Up the ONS 15454 SDH for Firewall Access

Purpose

This procedure provisions ONS 15454 SDH nodes and CTC computers for

 

access through firewalls.

Tools/Equipment

IIOP listener port number provided by your LAN or firewall administrator

Prerequisite Procedures

NTP-D24 Verify Card Installation, page 4-2

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Step 1

Log into a node that is behind the firewall. See the “DLP-D60 Log into CTC” task on page 3-24for

 

instructions. If you are already logged in, continue with Step 2.

Step 2

Complete the “DLP-D67 Provision the IIOP Listener Port on the ONS 15454 SDH” task on page 4-20 .

 

Figure 4-5shows ONS 15454 SDH nodes in a protected network and the CTC computer in an external

 

network. For the computer to access the ONS 15454 SDH nodes, you must provision the IIOP listener

 

port specified by your firewall administrator on the ONS 15454 SDH.

 

Figure 4-5 ONS 15454 SDH Nodes Residing Behind a Firewall

Firewall

Unprotected

Private

IIOP port ONS 15454 SDH

network

network

CTC computer

External network

IIOP port

Port

 

 

filtering

ONS 15454 SDH

 

 

61331

Protected network

 

 

 

Cisco ONS 15454 SDH Procedure Guide, R4.6

 

 

 

 

 

 

January 2004

 

 

4-19

 

 

 

 

 

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Before You Begin Turn Up NodeInstall Cards and Fiber-Optic Cable NTP-D24 Verify Card InstallationStop. You have completed this procedure DLP-D74 Create a New User-Single Node NTP-D30 Create Users and Assign SecurityDLP-D75 Create a New User-Multiple Nodes Required/As Needed PurposeClick the Provisioning General tabs Confirmation dialog box, click Yes Node view, click the Provisioning General Power Monitor tabs NTP-D279 Set Power Monitor ThresholdsNTP-D169 Set Up CTC Network Access Click the Provisioning Network tabs DLP-D249 Provision IP SettingsCisco ONS 15454 SDH Procedure Guide, R4.6 Reboot Activity Active TCC2 LEDs Standby TCC2 LEDs Slot-0 Status=IpAddress Next Done Mod Cisco ONS 15454 SDH Reference Manual DLP-D65 Create a Static Route Click the No Authentication button DLP-D250 Set Up or Change Open Shortest Path First Protocol Type- Choose Simple Password January DLP-D251 Set Up or Change Routing Information Protocol NTP-D27 Set Up the ONS 15454 SDH for Firewall Access Iiop port Port Function DLP-D68 Provision the Iiop Listener Port on the CTC Computer NTP-D28 Set Up TimingStop . You have completed this procedure DLP-D69 Set Up External or Line TimingUnframed , FAS , FAS + CAS DLP-D70 Set Up Internal Timing NTP-D170 Create Protection Groups Type Cards Description and Installation Requirements DLP-D71 Create a 11 Protection Group Click the Provisioning Protection tabs DLP-D72 Create a 1N Protection GroupDLP-D73 Create a 1+1 Protection Group Creating a Y-Cable Protection Group DLP-D252 Create a Y-Cable Protection GroupBox Figure NTP-D34 Set Up SnmpCreating an Snmp Trap Without Proxy January
Top Page Image Contents